User manual AEG-ELECTROLUX HC8830EN
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX HC8830EN. We hope that this AEG-ELECTROLUX HC8830EN user guide will be useful to you.
Manual abstract: user guide AEG-ELECTROLUX HC8830EN
Detailed instructions for use are in the User's Guide.
[. . . ] You should receive: 1 - assembled hood 1 - plastic bag, containing: 4 - 7/8" wood screws for mounting hood to cabinet 2 - 1/4" black sheet metal screws for mounting damper/ duct connector to hood 2 - aluminum filters 1 - damper/duct connector For Ductfree Installations Only: Discard damper/duct connector and two black sheet metal screws. b. ) Loosen knurled nuts on mounting rods and slip rods out of blower mounting brackets. 3
VERTICAL DUCTING*
ELECTRICAL KNOCKOUTS
HINGE PINS DUCT KNOCKOUTS*
HORIZONTAL DUCTING* HINGE PINS * FOR DUCTED INSTALLATIONS ONLY.
3
PREPARE THE INSTALLATION LOCATION
NOTE IF DISTANCE BETWEEN WALL AND FRONT OF CABINET FACE FRAME IS MORE THAN 12", THERE WILL BE A GAP BETWEEN BACK OF HOOD AND WALL. TOP FRONT EDGE OF HOOD SHOULD BE FLUSH WITH FRONT OF CABINET FACE FRAME. [. . . ] Fasten wall cap to last section of duct and nail or screw cap to wall. Make sure that enough duct runs into the room so that the duct will overlap the damper/duct connector by 3/4" when the hood is installed.
a. ) electrical wiring runs through opening in top or back of hood. b. ) large part of keyhole slots fit over hood mounting screws For Ducted Installations Only: c. ) damper/duct connector slides into ductwork. Push hood back so that mounting screws slide into narrow end of keyhole slots. holes (in hood top and 8" each side of center) and into the cabinet bottom or added filler strips. Connect white to white, black to black, and green or bare wire to green ground screw. 7B
3/4"
BLACK
K AC BL
PLASTIC ROOF CEMENT
WH ITE
WH ITE
FIG. 7D
NAIL
BLACK WHITE GREEN GREEN
GROUND (BARE OR GREEN WIRE)
CK BLA
DO NOT CAULK AROUND BOTTOM OF FLANGE FOR DRAINAGE
ROOF CAPS (FIGS. 7A - 7D) Cut hole in roof slightly larger than duct so duct will line up easily with hood. Trim shingles around hole so that they will fit snugly around hood of cap when cap is installed. Trim duct parallel to roof pitch, leaving 3/4" of duct projecting above roof (FIG. (FIG 7C) Seal around roof cap with roof cement and seal all nail heads and shingles which were cut or lifted. 7D) Make sure that enough duct runs into the room so that the duct will overlap the damper/duct connector by 3/4" when the hood is put into place.
5. Install 25 watt bulb in righthand socket.
5
WH
ITE
INSTALL HOOD (Continued)
For Ducted Installations Only:
FIG. 10
BLOWER DISCHARGE
INSTALL HOOD (Continued)
For Ductfree Installations Only: 9. 13) Make sure that tab on aluminum filter lines up with finger pull on replacement filter.
FIG. Position blower so that blower discharge lines up with damper/duct connector and slip rods into mounting brackets on blower assembly. 10) Tighten knurled nuts securely, and plug in blower.
For Ductfree Installations Only:
FIG. 14) Push assembly up until bottom of assembly clears lip on bottom cover. Insert bottom of filter and pull assembly down, collapsing pull ring against aluminum filters.
FIG. [. . . ] LIGHT Three-position switch · First position (Normal) - Turns both bulbs ON. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface. 2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed. When the temperature level drops to normal, the blower will return to its original setting. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX HC8830EN
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX HC8830EN will begin.