User manual AIPTEK PENCAM TRIO VGA PC0V

[. . . ] @n IP Company AIPTEK PENCAM Installation Guide Contents FCC Statement ECC Statement End User License Agreement Contents Checklist System Requirements Specifications Operating Environment How to Use Your PenCam Switching the camera on Taking a picture 1 2 5 6 7 8 Additional features Self Timer Continuous mode Clearing the stored images Changing the picture resolution 9 10 How to Upload Photo & Video to PC Start Aiptek PenCam Manager Mode Selecting PC Camera Mode DSC Mode Uploading Photos Editing Photos Uploading Video AVI Creator Playing Video Image processing 11 12 13 14 15 16 17 Troubleshooting How To Obtain A Warranty Service Statement of Limited Warranty Mail Function 18 19 22 @n IP Company FCC Statement This equipment generates and uses radio frequency energy and if not installed and used in accordance with the manufacturer's instructions, it may cause interference to radio and television reception. This equipment has been tested and certified to comply within the limits of Section 15(J) of FCC Regulations for Class B computing devices. These regulations are desi gned to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] 8 . . @n IP Company Self Timer Pressing the mode button until "St" appears in the LCD then pressing the shutter button will start a 10 second self-timer. The camera will issue a short beep every second and then a longer beep. Note: The self-timer can not be selected when the camera is full. SW1 Switch mode to "St" "St" will be displayed Press SW1 to initiate the self-timer mode Continuous mode Pictures may be taken continuously as long as the shutter button is pressed(and the camera is not full) as follows: Press the mode button until the Ct appears in the LCD. Pressing the shutter button within 5 seconds will cause the camera to start taking pictures for as long as the shutter button is held down. If the shutter button is not pressed within 5 seconds the camera will revert back to normal picture taking. Note: During the continuous mode the camera will allow pictures to be taken with incorrect exposure. SW1 Switch mode to "Ct" "Ct" will be displayed Press SW1 to utilize Continuous mode . . 9 . . Clearing the stored images Press the mode button until CL appears on the LCD. Pressing the shutter button once will cause the camera to beep and the CL will start flashing . Pressing the shutter button again within 5 seconds will clear the camera and reset the picture counter. SW1 Switch mode to "CL" "CL" will be displayed Press SW1 to select clear mode LCD will start flashing Click SW1 twice to clear the memory Changing the picture resolution Picture resolution may only be changed when the camera memory is empty. If any pictures have been taken then the memory must first be cleared. To change resolution press the mode switch until the resolution option is displayed, either Hr to change to high resolution mode (if you are currently in the low resolution mode)or Lr to change to low resolution(if you are currently in the high resolution mode). The camera will beep and the display will reset to indicate the number of pictures available. SW1 Switch mode to "Hr" or "Lr" "Hr" or "Lr" will be displayed Press SW1 to change resolution . . 10 . . @n IP Company How to Upload Photo & Video to PC PenCam Manager Installation Thank you for purchasing the Aiptek PenCam. This guide will walk you through the steps of how to install the PenCam onto your computer system. Place the CD into your CD-ROM and click on the PenCam Manager Icon to begin the installation. If the CD does not automatically display, simply go to "Start" then "Run" and select the path "D:\Setup. exe". You may need to replace "D" with the letter that corresponds to your CD-ROM drive. Please wait. The welcome screen will appear, then click "Next"? The CD will begin installing the driver to the proper location. The dialog box that appears asks if you would like to restart your computer now or later. 11 . . Start Aiptek PenCam Manager Stored pictures may be uploaded to a PC at any time whether or not the camera is full. When connected to the PC the camera may be used as a normal PC camera. Connect the smaller end of the USB connector to the side of the camera. Plug the other end of the USB connector into an available USB port on your computer. Note:When plugged into a USB port the camera gets its power from the PC. However, all pictures will be lost when the USB connector is unplugged. To start using the PenCam Manager, simply click on the "Start" menu and go up to "Programs" Then go to the folder named "PenCam" and select it. 12 . . @n IP Company Mode Selecting = Press the "Live View" button to switch the camera to PC Camera mode. [. . . ] If this HARDWARE PRODUCT is purchased from an unauthorized reseller, the Limited Warranty will be null and void, and Aiptek will have no obligation to provide the Warranty Service. See the "List of Authorized Resellers" in the manual to determine whether or not you purchased the HARDWARE PRODUCT from an Authorized Reseller. Only the End-User who has registered the product and who has kept a copy of the original receipt may receive the Warranty Service. No other representatives of the End-User's household, and no other representatives . . [. . . ]