User manual AKAI ATE-48N1104K

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Size: When the input source is YPbPr 1, YPbPr 2, VGA or HDMI, press this button, the picture will change according to Fill All, Force 4:3, Letter Box, Wide or Anamorphic. When the input source is AV or S-Video, press this button, the picture will change according to Fill All, 4:3, Letter Box, Wide or Anamorphic. 22 PIP Size : Press the button to select different Image Size in PIP Mode. 25 Sleep: Press this button to select the sleep time. Insertion of Batteries: - Turn the remote control upside down, press and slide off the battery cover. - Insert two 1. 5V (AAA) batteries into the compartment, take care to observe the markings indicated inside. - Replace the cover and slide in reverse until the lock snaps. and 13 Range of Remote Control Sketch map 20 20 30 30 - Ensure the remote control is pointed towards the remote control window on the display unit. - No obstacles should be placed between the remote control and the remote control window. - The effective receiving range for the signal is within 5-8 meters from the front of the remote control window, and 30° to the left or right side and 20° above or below the control window. Care For Remote Control - Avoid spilling liquids on the remote. - Always store the remote control at dry and normal room temperature place. - If the remote is nor performing satisfactorily, replace the batteries. - If the remote control will be idled for a long time (above 1 month) take out the batteries to avoid leakage from the batteries. To watch the VCR or other video apparatus, please press SOURCE button to select S-VIDEO or AV. white red red white VCR etc. VCR etc. 17 6. Basic Operation 6. 1 Power ON/OFF: The Display is in Standby mode - Press Standby ( ) button on the remote control or on the front panel to turn on the unit. - Press Standby ( ) button on the remote control or on the front panel again to return the display to standby mode. Note: For protecting your PDP product, the interval time between turn on the PDP product and shut down it should be kept at least one minute. 6. 2 Selection of Input Mode - Press Source button on the remote control or on the front panel. Press or to select the signal source you desired and press OK / to confirm the selection. The signal sources are displayed in the following sequence: Source Select: AV S-Video YPbPr 1 YPbPr 2 VGA HDMI When select the input source, the screen will display the direction. AV Searching Fill All AV NTSC 60Hz/3. 58 MHz When there is no signal from the selected source (see illustration), either change the channel or press Source button to change sources. If there is no signal on your selected source for 15 minutes the television will power down. S-Video Searching ! S-Video No Input Power Off In 15 Minutes 18 6. 3 Other Function Swap: - Press this button on remote control to switch the Main window or Sub window picture in PIP or Split Screen. Sele: - Press this button to select the sound output from Main Window or Sub Window. - When you want to select the signal source from the Main Window or Sub Window, you can press Source button to pop up "Source Select" menu, then use or button to select the signal source and press OK or to confirm. Display: - Press this button to show the source's information as follow: 01 : 01 AM Fill All AV NTSC 60Hz/3. 58MHz 01 : 01 AM Fill All VGA 700x566/50Hz AV Mode 01 : 01 AM MainVGA 700x566/50Hz SubAV NTSC 60Hz/3. 58MHz 01 : 01 AM Main: VGA 700x566/50Hz Sub: AV NTSC 60Hz/3. 58MHz VGA Mode PIP Mode Split Screen Mode Auto: - Press this button to adjust the phase, vertical / horizontal position in VGA Mode only. PIP POS. : - Press this button to pop up the "PIP Position" item, then press / button to select different PIP position in PIP Mode. PIP Size: - Press this button to pop up the "PIP Size. " item, then press / button to select different PIP Size in PIP Mode. [. . . ] - When the signal received by the Display exceeds the allowed range, a warning message shall appear on the screen. - You can confirm the input signal format from the on-screen. 33 9. Cleaning and Simple Troubleshooting 1 Important: - Make sure that the power cable is removed from the AC outlet before cleaning the product. - Do not use volatile solvent (such as toluene, rosin and alcohol) to clean the Display. [. . . ]