User manual AMX 10.4 TOUCH PANELS (G3 FIRMWARE)

[. . . ] instruction manual 10. 4" Touch Panels (Firmware version G3) Tou c h Pa n els an d A cc e ss o r ie s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] Syntax: "'AKEYB-<text string>'" Variable: text string = 0 - 59 characters Example: SEND_COMMAND TP, "'AKEYB-TOUCH HERE'" Opens the touch panel keyboard with TOUCH HERE in the display. AKEYP Opens the touch panel keypad and initializes the number string entry. The keyboard string is set to null during power-up and stored until power-down. Syntax: "'AKEYP-<number string>'" Variable: number string = 0 - 9999 Example: SEND_COMMAND TP, "'AKEYP-1988'" Opens the touch panel keypad with 1988 in the display. Syntax: "'AKEYR'" Example: SEND_COMMAND TP, "'AKEYR'" Closes the keyboard/keypad opened using the 'AKEYB', 'AKEYP', or 'PKEYP' commands. 28 10. 4" Touch Panels Programming System Send_Commands (Cont. ) BAUD Sets the program port baud rate. The baud rate can also be set in the Protected Setup page's BAUD level indicator. Syntax: "'BAUD <baud rate>'" Variable: baud rate = 38400, 19200, 9600, 4800, 2400, 1200, 600, and 300 Example: SEND_COMMAND TP, "'BAUD 38400'" Sets the Baud rate to 38400. BEEP This beep command sounds one tone for a time length of 50 milliseconds. "'BEEP'" Example: SEND_COMMAND TP, "'BEEP'" Activates one beep tone. BRIT Syntax: Adjusts brightness "'BRIT-<level>'" of display. Variable: level = 1 - 8 (1 = minimum; 8 = maximum) Example: SEND_COMMAND TP, "'BRIT-8'" Sets to highest brightness level. Syntax: "'CALIBRATE'" Example: SEND_COMMAND TP, "'CALIBRATE'" Starts the calibration operation on the touch panel. Syntax: "'CLOCK <mm-dd-yy> <hh:mm:ss>'" Variables: mm = 01 - 12, dd = 01 - 31, yy = 00 - 99 hh = 00 - 23, mm = 00 - 59, ss = 00 - 59 Example: SEND_COMMAND TP, "'CLOCK 02-08-98 19:16:00'" Sets the touch panel's date to February 8, 1998, and time to 7:16 p. m. CURSOR Syntax: Turns the cursor "'CURSOR <OFF/ON>'" display On or Off if Variables: the touch device Off = 0 and On = 1 has a cursor. Example: SEND_COMMAND TP, "'CURSOR 0'" Turns the cursor display Off. 10. 4" Touch Panels 29 Programming System Send_Commands (Cont. ) DBEEP Gives a double beep output. This command only works if the Double Beep value in the Protected Setup page is set to On. Syntax: "'DBEEP'" Example: SEND_COMMAND TP, "'DBEEP'" Double beeps the panel. Syntax: "'ILEV <joystick axis to invert>'" Variables: joystick axis to invert = 0 : Normal G3 joystick (origin: top left) 1 : Invert horizontal axis (origin: top right) 2 : Invert vertical axis (origin: bottom left) 3 : Invert both axes (origin: bottom right) Example: SEND_COMMAND TP, "'ILEV 3'" Inverts the joystick axis to move the origin to another corner. Syntax: MOUSE <mouse type> Variables: mouse type = 00: Mouse cursor Off 01: Microsoft® serial mouse/cursor On 8000: Touch Output to Serial Port 8000 (Elo IntelliTouch) Example: SEND_COMMAND TP, "'MOUSE 01'" Turns on Microsoft® compatible serial mouse. Refer to the @MOU section on page 40 for the chart describing the BIT information and definitions. Syntax: "'PAGE-<page name>'" Variable: page name = 1 - 50 ASCII characters Example: SEND_COMMAND TP, "'PAGE-MAIN PAGE'" Flips the touch panel to the page named MAIN PAGE. Syntax: "'PKEYP-<number string>'" Variable: number string = 0 - 9999 Example: SEND_COMMAND TP, "'PKEYP-1988'" Displays the touch panel keypad with **** instead of 1988. 30 10. 4" Touch Panels Programming System Send_Commands (Cont. ) PPOF Closes a specific popup page. [. . . ] Return the touch panel to the CB-TP3 or equipment rack, and reconnect all external connectors. Make sure that the release slot is located at the bottom of the touch panel. Make sure the unit is securely attached to its new location. 10. 4" Touch Panels 59 Changing the LCD Viewing Angle Jumper 6 321 FIG. 20 Open circuit card and JP6 jumper location Bezel mounting screws Rotate bezel 180 degrees Bezel/faceplate Release slot FIG. [. . . ]