User manual AMX FOLD OUT-CC-IRC IR EMITTER CABLE

[. . . ] AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. [. . . ] This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. The owner is advised to consult applicable state laws for full determination of rights. · fold EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. 041-004-2606 2/06 ©2006 AMX Corporation. All Rights Reserved. 93-0000-11 Rev E 041-004-2606 2/06 ©2006 AMX Corporation. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation. AMX reserves the right to alter specifications without notice at any time. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation. AMX reserves the right to alter specifications without notice at any time. *In Canada doing business as Panja Inc. 3000 research drive, richardson, TX 75082 USA 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 technical support 800. 932. 6993 brussels · dallas · los angeles · mexico city · philadelphia · shanghai · singapore · tampa · toronto* · york 3000 research drive, richardson, TX 75082 USA 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 technical support 800. 932. 6993 brussels · dallas · los angeles · mexico city · philadelphia · shanghai · singapore · tampa · toronto* · york cut CC-IRC Controlled Equipment (DVD, CDP, VCR, etc. ) Infrared Emitter Control System Accessories CC-IRC Infrared Emitter Control System Accessories cut cut cut fold fold fold 93-0000-11 Rev E cut cut CC-IRC IR Emitter Overview The IR Emitter adheres directly to the IR control window of your equipment by using clear two-sided tape to securely adhere the opaque shield. This "standard configuration" allows you to control your equipment either from either IR emitters or a hand-held remote control. The two black adhesive-backed window shields (Figure 3) are included within each emitter package and allow for alternate configurations. With this shield (surrounding the internal emitter), you can restrict IR reception through the device's control window by blocking any interference or IR signals produced by sources other than the internal emitter. [. . . ] The IR LED can then be reversed or removed when the shell is Figure 2 separated. Once the IR emitter and/or shield installations have been completed, the housing can be re-assembled by pressing the two halves firmly together. Removing the Factory-Installed Shell The factory-installed shell is easily removed by carefully separating the two halves with a sharp-edged tool, such as an X-ActoTM knife. The IR LED can then be reversed or removed when the shell is separated. Once the IR emitter and/or shield installations have been completed, the housing can be re-assembled by pressing the two halves firmly together. Figure 2 Shielded Configuration Use this configuration to prevent interference from fluorescent lights or other IR sources. [. . . ]