User manual AOC V22T

[. . . ] 11. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 13. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 14. The TV should be operated only from the type of power source indicated on the label. [. . . ] Turn on the LCD Switch on the AC power supply on the back of the TV set and press the Power key on the remote controller or press the Power key on the panel. The indicator will turn blue and the LCD TV will enter normal operating mode several seconds later. 2. Turn off the LCD Press the Power key on the remote controller or press the Power key on the panel to turn off the LCD. 3. . Off, the blue TV indicator goes off after flashing three times. Searching Press the "TV" key on the remote controller to switch to the TV signal source, then press the "Menu" key on the remote controller or the "Menu" key on the right side of the panel to enter the main menu page. Press the Searching key or enter the searching page to search channels automatically. Suggestion: select Auto for the color system and DK for the sound system. To select automatic searching: It will search for all TV programs and save them to the memory. Normally TV programs can be watched after the above steps are completed. In case of any abnormality or to further understand the unit, read the following contents. About the control panel and interface PANNEL CONTROL KNOBS Input: Menu: CH/ : Vol / : Press this button to change input source. When the OSD menu appears, press these two buttons to select the item you want to execute; when no OSD menu appears, use to change channels in TV mode. When the OSD menu appears, press these two buttons to select or adjust the selected item; when no OSD menu appears, use to adjust the volume. SOURCE INTERFACE Several signal source devices can be connected to your TV set. Tips: If you want to hang the TV set on the wall, all connecting wires must be inserted into the interfaces of the TV set first. Whenever a peripheral device is connected to the TV set, ensure that the TV set is turned off. When connecting a peripheral device, connect the cable to the connecting terminal that is the same color as the cable color. SOURCE INTERFACE Antenna Input: Insert the antenna connector into the antenna jack of the TV. The interface is a 75 coaxial cable input. Video/S-terminal input Connect the video signal source or S-terminal cable to a device such as a DVD, laser disc player, video recorder or camera. Audio input: Connect the audio signal source (computer, DVD, laser disc player, video recorder or camera, etc. ) to the audio input port. In case of any barriers between the main unit and the remote controller, the remote controller may not work. Note: To ensure safe operation, please do the following: 1. Avoid letting the remote come into contact with water or other liquids. If the battery liquid leaks inside the remote controller, carefully clean the battery compartment and insert new batteries. Dispose of used batteries according to the instructions on the battery. TO USE THE MENU 1. Use the P- or P+ to enter into the submenu, or to enable or adjust the selected function. Press the Menu button to exit the Main Menu. SOURCE MENU Press the Source button to enter the Source Menu: PC, HDMI, AV, S-Video, Component, TV. TO USE THE MENU Picture Setting Brightness Contrast Saturation Sharpness Color Temp. DNR Picture Mode DCR Reset Adjustable between 0-100, set the backlight brightness of the picture. [. . . ] S-VHS video recorder or camera) simultaneously, the quality of the picture will be poorer. Turn off other peripheral devices in this case. double No power Dots of constant color appear on the TV screen No sound or picture, and the red lamp on the front panel doesn't go on No image appears Good picture but no sound No sound for some channels Sound is OK but color is poor Poor picture quality Before Calling Service Snowy picture and noise Horizontal dotted line Television not responding to remote control VGA mode doesn't work *Check the antenna connection *This may be caused by electrical interference (e. g. Check the settings of the display card Change the refresh frequency of the PC to 60 Hz. Black stripes appear on the top and bottom of the screen in VGA mode GLOSSARY Audio / Video Inputs Located on the rear and the front of the receiver these connectors (RCA phono type plug) are used for the input of audio and video signals. Designed for use with VCRs (or other accessories) in order to receive higher picture resolution and offer sound connection options. [. . . ]