User manual ARTHUR MARTIN DE0260W2

[. . . ] Do not attempt to modify the hob in any way. Child Safety This hob is designed to be operated by adults. Children can also injure themselves by pulling pans or pots off the hob. During Use This hob is intended for domestic cooking only. This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. [. . . ] A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition electrode The electric ignition is obtained through a ceramic electrode and a metal electrode (Fig. Keep these components very clean, to avoid difficult lighting, and check that the burner crown holes (Fig. B) are not obstructed. 7 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles. after cleaning. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any inguarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 8 Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk When you contact the Service Centre, they will need the following information: 1. Your telephone number Clear and concise details of the fault The model and the serial number (see rating label on the back of this instruction booklet) Date of purchase Customer Care For general enquiries concerning your AEG-Electrolux appliance and for further information on AEG-Electrolux products, contact our Customer Care Department by letter or telephone at the address below or visit our website at www. aeg. co. uk Customer Care Department AEG-Electrolux Domestic Appliances 55 - 77 High Street Slough Berkshire SL1 1DZ Tel : 08705 350350* * calls to this number may be recorded for training purposes. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to R 1/2" (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. FO 0814 FO 0264 It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. 13 Cut Out Size The dimensions of the cut-out are given in the diagram. 68 0 51 0 FO 2038 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 (see next page). 14 1 ON/OFF SWITCH ON/OFF SWITCH 2 FLEX OUTLET FLEX OUTLET FO 2563 FO 2564 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 3 FO 2044 Dimensions are given in mm. 15 Fitting the Hob into the worktop Carry out the building in of the hob as follows: · put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. [. . . ] between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C. Replacement of the cable The connection of the voltage cable to the appliance's terminal block is of type "Y". [. . . ]