User manual ASUS P8Z77-V LK

[. . . ] No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK Computer Inc. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Offer to Provide Source Code of Certain Software This product may contain copyrighted software that is licensed under the General Public License ("GPL") and under the Lesser General Public License Version ("LGPL"). [. . . ] Sets the front panel audio connector (AAFP) mode to legacy AC'97 SPDIF Out Type [SPDIF] [SPDIF] [HDMI] Sets to [SPDIF] for SPDIF audio output. Realtek PXE OPROM [Disabled] This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE OptionRom of the Realtek LAN controller. 0 Battery Charging Support [Disabled] [Enabled] [Disabled] This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the USB 3. Serial Port Configuration Serial Port [Enabled] The sub-items in this menu allow you to set the serial port configuration. Configuration options: [Enabled] [Disabled] This item appears only when you set the Serial Port to [Enabled] and allows you to select the Serial Port base address. 7 APM EFI BIOS Utility - Advanced Mode Exit Main Back Ai Tweaker Advanced\ APM > Advanced Monitor Boot Tool Restore AC Power Loss Power On By PS/2 Keyboard Power On By PCIE/PCI Power On By Ring Power On By RTC Power Off Disabled Disabled Disabled Disabled Allow BIOS yo switch off some power at S5 to get the system ready for ErP requirement. Restore AC Power Loss [Power Off] [Power On] [Power Off] [Last State] The system goes into on state after an AC power loss. The system goes into either off or on state, whatever the system state was before the AC power loss. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Power On By PS/2 Keyboard [Disabled] [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Chapter 3 3-24 Power On By PCIE/PCI [Disabled] [Disabled] [Enabled] Disables the PCIE/PCI devices to generate a wake-on-LAN feature of the Intel/Realtek LAN device. Enables the PCIE/PCI devices to generate a wake-on-LAN feature of the Intel/Realtek LAN device. Power On By Ring [Disabled] [Disabled] [Enabled] [Disabled] [Enabled] Disables Ring to generate a wake event. When set to [Enabled], the items RTC Alarm Date (Days) and Hour/ Minute/Second will become user-configurable with set values. Power On By RTC [Disabled] Chapter 3: BIOS setup RTC Alarm Date (Days) This item appears only when you set the previous item to [Enabled] and allows you to select RTC alarm time (days). 8 Network Stack EFI BIOS Utility - Advanced Mode Exit Main Back Network Stack Ai Tweaker Advanced\ Network Stack > Advanced Monitor Boot Tool Disabl Link Allow BIOS yo switch off some power at S5 to get the system ready for ErP requirement. 6 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings. Scroll down to display the following items: Chapter 3 3-26 Chapter 3: BIOS setup CPU Temperature / MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures. Select Ignore if you do not wish to display the detected temperatures. CPU Fan Speed [xxxx RPM] or [Ignore] / [N/A] Chassis Fan 1/2/3 Speed [xxxx RPM] or [Ignore] / [N/A] The onboard hardware monitor automatically detects and displays the CPU and chassis fan speed in rotations per minute (RPM). 3V Voltage, 5V Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. CPU Fan Speed Low Limit [200 RPM] This item appears only when you enable the CPU Q-Fan Control feature and allows you to disable or set the CPU fan warning speed. Configuration options: [Ignore] [100 RPM] [200 RPM] [300 RPM] [400 RPM] [500 RPM] CPU Fan Profile [Standard] This item appears only when you enable the CPU Q-Fan Control feature and allows you to set the appropriate performance level of the CPU fan. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Increase the separation between the equipment and receiver. [. . . ]