User manual ASUS RAMPAGE IV GENE

[. . . ] Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. The use of a shielded-type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio and television reception. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Reprinted from the Code of Federal Regulations #47, part 15. 193, 1993. [. . . ] Government Printing Office. UL This product meets all safety requirements per UL-1950 standard. CE This certificate of conformity is based on an evaluation of the cable modem that is in compliance with the Low Voltage Directive 73/23/EEC and the Amendment Directive 93/68/EEC. Cable Modem User's Manual 3 Contents Chapter 1 - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing a Network Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Checking if TCP/IP is already installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Adding TCP/IP in Network properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Changing TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 2 - Installing the Cable Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Powering Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connect the DC power adapter to the POWER input jack on the rear panel of the cable modem. NOTE: If you are not using a television on the cable line, you may skip steps 1 to 3 and connect the cable TV coaxial cable directly to the CABLE connector on the rear panel of the cable modem. Splitter Chapter 2 8 Cable Modem Ca bl eM od em To Cable Network 2-Way Splitter TV Computer Cable Service Connections Cable Modem User's Manual Chapter 2 - Installation Powering Up When all connections have been properly made and the power is ON, the cable modem will automatically start the self-test and search for the active cable channel provided by your cable operator. Now you are all set and ready to surf the Internet at a marvelous speed! Multiple Client Configuration The cable modem supports up to 15 pieces of consumer premises equipment. If you can obtain multiple IP addresses from your cable operator, you can hook up as many computers to the cable modem as the number of the IP addresses, using a hub in-between (as shown below). Each connected client PC will then be assigned one dynamic IP address by the cable operator. Chapter 2 9 Client Ca To Splitter or Cable Network bl eM od Client em Cable Modem Ethernet Hub Client Multiple Client Configuration Diagram Cable Modem User's Manual Chapter 2 - Installation If you would like to use the USB interface, connect the USB cable modem to your computer using the USB cable and install the driver as shown here. Windows ME Installing the Driver 1. If you have not connected the cable modem to your computer using the USB cable, do so now. Windows will detect that a new hardware has been added and will start the Add New Hardware Wizard. The Wizard searches for the driver and finds the correct device driver. After the initial setup files are copied, the wizard indicates it has completed he driver installation. Click Yes. Chapter 2 10 Cable Modem User's Manual Chapter 2 - Installation Windows ME Verifying the Driver 1. You should see "USB Cable Modem " Chapter 2 Deleting the Driver - Network (Either the Network or System will work. ) 1. [. . . ] Select the device and click the remove button. Deleting the Driver - System (Either the Network or System will work. ) 1. Right-click "My Computer" icon on the desktop and select Device Manager. Select the device and click the remove button. Cable Modem User's Manual 11 Chapter 2 - Installation Windows 2000 Installing the Driver 1. If you have not connected the cable modem to your computer using the USB cable, do so now. [. . . ]