User manual AT&T E5901

[. . . ] User's manual E5901/E5902B/E5903B 5. 8 GHz cordless telephone with caller ID/call waiting Congratulations on your purchase of this AT&T product. Before using this AT&T product, please read the Important safety instructions on pages 44-46 of this manual. Please thoroughly read the user's manual for all the feature operation and troubleshooting information you need to install and operate your new AT&T product. For customer service or product information, please visit our website at www. telephones. att. com or call 1 (800) 222-3111. [. . . ] LIST FULL MUTED SPEAKER LOW BATTERY INCOMING CALL NEW VOICE MAIL You are saving to a full directory. There are new voice mail messages. XX MISSED CALLS There are new calls in the caller ID log. ** PAGING ** HANDSET X IS CALLING LINE IN USE NO LINE ALREADY SAVED SAVED WARNING CHECK BATTERY!The telephone number you have entered is already stored in the directory. The battery is not installed or not installed properly in the handset while in the charger or telephone base. Use only the supplied rechargeable battery or replacement battery (model 27910, part number 89-0099-00-00). The handset should be placed in the telephone base or charger. -OR-OR- 34 Appendix Handset display screen messages Screen display messages CHARGING UNABLE TO CALL TRY AGAIN NOT AVAILABLE AT THIS TIME MICROPHONE ON INTERCOM TO A handset with a low battery has been placed in the telephone base or charger. Failed intercom or conference call (there are already two handsets being used). Someone else is already using the directory or call log when you try to do so. (You have to press the handset number of the destination handset. ) The intercom call has just been ended by you or the receiver of the call. The handset is to transfer a put-on-hold external call to another handset. The handset is out of range while on a call. INTERCOM ENDED CALLING HANDSET X TRANSFER TO NO SIGNAL, CALL ENDED 35 Appendix Adding and registering handsets Your telephone can accommodate up to four cordless handsets. You can add new handsets (E598-1 or E598-2, sold separately) to the E5901/E5902B/ E5903B anytime, but each handset must be registered with the telephone base before use. The handsets provided with your E5901 are pre-registered as handsets 1. Additional handsets will be assigned numbers in the order they are registered (handset 2, handset 3, or handset 4). You can register two additional handset, which will be assigned number 3 and 4. You can register one additional handset, which will be assigned number 4. NOT REGISTERED Handsets purchased separately need to be registered to the telephone base before use. When first purchased, all optional accessory handsets will show NOT REGISTERED on the screen. The new handset may need to be charged for five minutes before registering to the main telephone base. If PRESS HNDST LOC 4 SEC ON BASE does not appear on the handset screen after a few seconds, remove the handset and place it in the telephone base again. On the telephone base, press and hold HANDSET LOCATOR for about four seconds (until the red IN USE light on the telephone base turns on) and then release the button. The handset will show HS X REGISTERED and will beep if the registration is successful. NOTES: 1. [. . . ] If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty, this limited warranty also applies to repaired or replacement PRODUCT for a period of either (a) 90 days from the date the repaired or replacement PRODUCT is shipped to you or (b) the time remaining on the original one-year limited warranty; whichever is longer. 50 Appendix Limited warranty 4. This limited warranty does not cover: · PRODUCT that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water, or other liquid intrusion; or · PRODUCT that has been damaged due to repair, alteration, or modification by anyone other than an authorized service representative of the manufacturer; or · PRODUCT to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or · PRODUCT to the extent that the problem is caused by use with non-AT&T accessories; or · PRODUCT whose warranty/quality stickers, PRODUCT serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or · PRODUCT purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to products used for rental purposes); or · PRODUCT returned without valid proof of purchase (see item 6 below); or · Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit. To obtain warranty service in the United States of America, call 1 (800) 222-3111; In Canada, please dial 1 (866) 288-4268. NOTE: Before calling for service, please review the user's manual - a check of the PRODUCT controls and features may save you a service call. [. . . ]