User manual AUDIO TECHNICA ATLP60

[. . . ] Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on apparatus. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Caution: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. [. . . ] To re-install the dust cover, guide the dust cover hinges into the two hinge receptacles located at the back of the turntable housing. 4 English Initial Setup (continued) Setting the Pre-amp (Phono/Line) Switch For increased flexibility of use, this turntable has an internal stereo phono pre-amplifier. The Pre-amp Selector (Phono/Line) Switch is located on the back of the turntable. If the stereo system you are using has a PHONO input, set the Pre-amp Selector Switch to the “PHONO” position. If your stereo system does not have a PHONO input, set the Pre-amp Selector Switch to the “LINE” position and connect the turntable’s output cables to the AUX or other high-level input on your stereo system (described later) (Fig. Connect the red RCA-type pin-plug to the right channel input and the white RCA-type pin-plug to the left channel input of your stereo system (Fig. With the tone arm still fastened to the tone arm rest, slowly turn the turntable platter clockwise ten times, to make certain the automatic mechanism is fully cycled. Make sure the AC outlet supplies the proper voltage for the AT-LP60 you are using. 5 mm mini-plug (male)–is designed to fit most popular computer* audio inputs. It may also be used to connect the turntable’s RCA output to other equipment, including: • a stereo/boombox* equipped with a 3. To use either adapter cable, connect the turntable’s red and white RCAtype plugs to the cable adapter’s RCA-type jacks. * When using either cable adapter, always set the AT-LP60 turntable’s Pre-amp Selector Switch to the “LINE” position. ) NOTE: If connection is desired to a mono amplifier/speaker, make certain to use a stereo-to-mono adapter, available from your dealer or an electronic parts store. Inserting a mono plug in the stereo jack will disable one of the stereo channels. Other adapter cable configurations will be available from dealers and parts stores for connecting to devices needing different terminations. 5 mm Input The AT-LP60 connects without adapters to devices equipped with RCA connectors. For maximum flexibility, we have included two adapter cables to fit other popular audio inputs. figure 3 PHONO “AUX” Stereo System Input Jacks White Red AC Pre-amp Selector Switch PHONO LINE AC Operation Automatic Operation 1. The turntable will start and the tone arm automatically will move to the leadin groove. When the record has finished playing, the tone arm automatically will return to the tone arm rest and the turntable will shut off. Stop: To stop playing the record before it reaches the end, press the STOP button (Fig. The tone arm will lift and return to the tone arm rest, and the turntable will shut off. [. . . ] Prior to moving the turntable, always unplug it from the AC outlet and fasten the tone arm on the tone arm rest with the vinyl twist-tie. € • Specifications Type Platter Motor Speeds Wow and flutter Signal-to-noise ratio Cartridge Output level Pre-amp “PHONO” Pre-amp “LINE” Phono pre-amp gain Power Dimensions Net weight Furnished accessories Replacement stylus Belt drive turntable, fully automatic Aluminum DC servo-controlled 331/3 RPM, 45 RPM Less than 0. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A. Or an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date. [. . . ]