User manual BECKER 7800 PRO INSTALLATION GUIDE

[. . . ] 43 Connection of the speed signal (GAL) from the speedometer/ tachometer . 58 Subject to errors and technical changes 31 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 2. Symbols used in the Installation Guide G denotes instructions which are important for your safety and the safety of others. denotes instructions which are important for the installation and function of the unit. 3. [. . . ] Low - level = earth, high - level 12 V - 16 V A If the switch is not accessible: · Check which lead is routed to the reversing lamp. Connect a separate lead to the active lead of the reversing lamp and connect with socket A, pin 2. Screw released speedometer cable onto the speed sensor and connect the wires. Cable connections for the speed sensor Brown - earth (terminal 31) Black - power supply (terminal 15), 9 - 16V, 30 mA Blue/red - signal for socket A pin 1 A Installing the speed sensor in the speedometer cable In order to install the speed sensor, the speedometer drive cable must be cut at a straight section, in which the speed sensor is then inserted. When removing the speedometer cable from the vehicle, ensure that the location of the straight-routed section is determined and marked accordingly. Installation is illustrated without reference to any specific vehicle. In addition to the sensor, the following VDO universal parts are required: 1 x connecting piece 1040 1300 025 (VDO part number) 2 x knurled nuts 1040 1000 003 (VDO part number) 2 x hose sleeves 1040 1000 031 (VDO part number) 2 x dogs 1040 1000 049 (VDO part number) 2 x friction washers 1040 0900 003 (VDO part number) 2 x fuel washers 4. 0 KN07. 0570. 18 (VDO part number) 2 x washers KN11. 1904. 122 (VDO part number) A complete set can also be ordered from VDO (Part number X 39397106191). GAL signal Figure 1 Subject to errors and technical changes 45 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide Recommended tools: Cable installation tool for speedometer cables from VDO, Order No: 1999. 10. 13. 000. 110 If you require vehicle-specific parts, please consult the vehicle manufacturer or your nearest VDO branch. Figure 3 · ) · For protective hoses with wire netting, the hose and flex cable can be cut directly with the side-cutting pliers. Figure 4 Shorten the protective hose again at both ends up to the plastic sheathing. Check whether the ends of the flex cable still engage in the speedometer and the gearbox. Connect the union nut and hose sleeve (Figure 6) and push onto the hose ends (Figure 7). Connect friction washer to dog (Figure 8). Figure 5 · · Figure 6 · Figure 7 Figure 8 46 Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide · Remove grease from flex cable and connect dog to flex cable. Using a suitable installation tool, press the dog onto the flex cable (Figure 9). ) · When pressing in, ensure that the dog is securely positioned and that it runs smoothly. Figure 9 Pull the hose sleeve and nut as far as possible in the direction of the dog, to achieve approx. Screw the connecting piece and the speed sensor into the cable (Figure 12). Electrically connect the speed sensor using the extension cable from VDO (part number: 2152. 90 30 0100). Figure 10 · Figure 11 Figure 12 · Wire connections for the speed sensor Brown - earth (terminal 31) Black - power supply (terminal 15), 9 - 16V, 30 mA Blue/red - signal for socket A pin 1 Subject to errors and technical changes 47 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 10. Installation/ Removal of the OnlinePro · Installation: With this radio, a universal mounting for DIN installation slots is integrated. The unit is inserted into the installation slot and secured with the slides supplied. Subsequently, insert slides into the openings on the front of the unit until the first detent position (Fig. Subsequently, remove the slides. A B ) · The installation angle of the unit must not exceed 0° - 35° (vertical). C Removal: To remove the unit, it must first be unlocked. For this purpose, push in both slides to the second detent position, as shown in Figure A. Then remove the slides by pressing the springs on the right and left sides of the unit. If the unit was installed previously in another vehicle, it may be necessary to adjust the springs on the unit before installation. E (Gently press slide in the direction of 1 while at the same time moving the slide in the direction of 2). D 2 E 1 Subject to errors or technical changes 48 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 11. [. . . ] After starting, routes are calculated for all the destinations stored in the unit's destination memory. · · In Service Mode, select Route mode with the right rotary control and press to confirm. By selecting Yes and then pressing the right rotary control , the Route Mode is activated. To end the Route Mode, route guidance must be terminated, as described in the operating guide. · Subject to errors or technical changes 56 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 14. [. . . ]