User manual BEGLEC SMART BEAM

[. . . ] 3. 8--ID ADDRESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 9--EDITING CUSTOM PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 10--SPECIAL SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. 3. 11--WHITES SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. [. . . ] 3. 13--A CTIVATE THE PASSWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. PART 4 USING A DMX512 CONTROLLER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14. 4. 1--BASIC ADDRESSING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14. 4. 2--CHANNEL ASSIGNMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14. 4. 3--BASIC INSTRUCTIONS FOR DMX512 OPERATION. . . . . . . . . . . . . . . . . . . . . . 18. PART 5 APPENDIX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19. 5. 1--TROUBLE SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 . 5. 2--MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20. 1 PRODUCT (GENERAL) 1. 1 PRODUCT INTRODUCTION This product is designed for indoor use. Suitable applications include wash or effect lighting for architectural, stage, theatre or road show applications. Direct input of DMX512 signal allows the units to be controlled from any DMX512 controller. This product can be operated as a single unit or in multiple units for large applications. 1. 2 PRODUCT FEATURES LED FIXTURE * * * * * * * * * * RGB Dimmer 0-100% Strobe Built-in automatic programs Upload custom parameters to slave fixtures LED display Display control 'lock-out' Direct DMX512 input Independent ID address Different white colors setting 'Over-heat' protection 1 PRODUCT(GENERAL) 1 2009. 11. 10 1. 3 TECHNICAL SPECIFICATIONS LED MODULE LED MODULE: Voltage Rated Power LED/Unit 100~250V. . . 50/60Hz 52W 14 X 3W Tri-RGB ~40 Environment Temperature -20 Cooling Dimensions Weight Direct air convection 245 x 205 x 245mm 4. 8Kg 1 PRODUCT(GENERAL) 2 2009. 11. 10 1. 4 PHOTOMETRIC DATA 1 PRODUCT(GENERAL) 3 2009. 11. 10 1. 5 SAFETY WARNING IMPORTANT ALWAYS READ THE USER MANUAL BEFORE OPERATION. PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA. This product must be installed by a qualified professional. A minimum distance of 0. 5m must be maintained between the equipment and combustible surface. Programs AT. 0 1 to AT. 1 0 are fully pre-programmed and will not be altered by changes in EDIT mode. Programs PR. 01 to PR. 10 are fully pre-programmed and can be edited in EDIT mode. 3 DISPLAY PANEL OPERATION 10 2009. 11. 10 3. 6 DMX512 SETTINGS DMX Enter the DMX mode to set the DMX ADDRESS. 3. 7 PERSONALITY PERSONALITY Enter the PERSONALITY mode to select DMX mode: TOUR Ar1. d , Ar1. s or HSV . , Arc. 1 , 3. 8 ID ADDRESS ID Enter the ID mode to set the ID ADDRESS. 3 DISPLAY PANEL OPERATION 11 2009. 11. 10 3. 9 EDITING CUSTOM PROGRAMS EDIT CUSTOM Enter the EDIT mode to edit the custom programs PR. 01 to PR. 10 . Each step allows the creation of a scene using RED Red , GREEN Green BLUE Blue , STROBE Strobe , TIME Time & FAD E Fade . , 3. 10 SPECIAL SETTINGS SETTING Select UPLD to upload the custom programs from the current MASTER unit to the SLAVE units. In order to activate the upload function the password must be entered. If an error occurs when uploading the MASTER and/or SLAVE units will display RED. On successful uploading of the custom programs the MASTER and SLAVE units will display GREEN. Enter ID in order to allow/disallow ID address function from the DMX512 controller. When RGBW is selected, on RGB = 255, 255, 255, the color is displayed as calibrated in CAL2 -- RGBW. When COLOR is set OFF , on RGB = 255, 255, 255, the RGB values are not adjusted and the output is most powerful. When [UC] is selected, the RGB output are adjusted to a standard preset universal color which balances fixtures from different generations. . 3 DISPLAY PANEL OPERATION 12 2009. 11. 10 Enter Dim to select dimmer mode and dimmer speed. [. . . ] The Dim 1/2/3/4 are speed modes of the non linear dimmer , Dim1 is the faster, while Dim4 is the slowest. The factory default setting is Dim4 . 3. 11 WHITES CALIBRATION CAL1 Enter the CAL1 to select white color of different color temperature. There are 11 pre-programmed White colors can be edited by using Red , Green & Blue , 3. 12 RGB CALIBRATION CAL2 Enter the CAL2 to adjust the RGB parameter to make different whites. When the new setting is activated, the DMX controller choose RGB = 255, 255, 255, the white color will be made by the actual RGB values on the CAL2 . 3. 13 ACTIVATE THE PASSWORD KEY Enter the KEY mode to select whether the access password is on or off. [. . . ]