User manual BLAUPUNKT LONDON RDM 104

[. . . ] Operating instructions London RDM 104 20 19 18 17 16 15 14 1 13 2 3 4 5 6 7 8 9 10 11 12 RADIO 7 CD 7 Table of contents Short description . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Operating the car radio with an automatic antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Switching between the memory levels (FM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Automatically storing the strongest stations with Travelstore . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If no station is found, then SPORT will flash in the display for approximately 3 seconds. The radio will then return to the mode it started in. which are stored under PTY SET in the DSC mode. If you would like to re-program the station buttons and change the language, please read the section on Programming with DSCPTY SET and PTY LANG. ENGLISH DEUTSCH Receiving traffic information stations with RDS-EON Many FM stations regularly transmit current reports on the traffic conditions in their broadcasting area. Stations transmitting traffic announcements broadcast an identification signal that your car radio can evaluate. If this signal is identified, then TP will appear in the display (Traffic Program). In addition to these, there are also stations which do not actually transmit traffic information themselves, such as NDR3, but by using RDS-EON they make it possible to receive the traffic messages broadcast by traffic information stations in the same station group. If you listen to one of these stations, then TP will also appear in the display as long as the traffic information priority feature has also been activated, i. Should a traffic announcement be broadcast, then the radio will automatically switch to the traffic information station in that group (in this case, NDR2). The traffic announcement will be played for its duration and then the radio will automatically switch back to the original program (NDR3). Traffic announcement priority While listening to the radio or to the CD player, you can choose whether or not traffic announcements should have priority or not. To switch the priority on or off · press the TIM button for longer than 2 seconds. TA will either light up or go out in the display. Use the rocker switch <</>> to set the desired value from T1 to T9. You can store different values for this setting separately on KeyCard 1 and 2. Switching the warning beep off In order to switch the warning beep off: ­ Select a different station. · · Press the rocker switch or / · Warning beep If you leave the reception area of the traffic information station you are currently listening to, then you will hear a warning beep after approximately 30 seconds. If you have switched on the AF function, SEARCH will soon appear in the display. If no alternative is found, then the warning beep will sound once again. Adjusting the volume for traffic announcements and the warning beep This volume was preset at the factory. If you would like to alter the setting, then proceed as follows: · Press the DSC button. · Then press the rocker switch / repeatedly until TA LEVEL appears in the display. press one of the station buttons on which a traffic information station is stored. TA will disappear in the display. ­ · Automatic station search start (CD mode) If you are listening to a CD and you leave the reception area for the traffic information station selected, then the car radio will automatically search for a new traffic information station. 38 Entering station names You can store different values for this setting separately on KeyCard 1 and 2. If you select a station, then its frequency, for example 96. 2, will appear in the display. If the station also transmits an RDS signal, then the station name will also appear afterwards, for example NDR2. [. . . ] · Press the PS/MIX button briefly. Proceed as described above in order to store other tracks. Playback with TPM In order to playback tracks you have stored with TPM · press the TPM button. · Use the rocker switch <</>>, to select CD1, for example. The tracks on all of the CDs stored with TPM will be played in ascending order. [. . . ]