User manual BOSCH MFQ2UC

[. . . ] • Unplug the appliance from the mains supply after each use, or if a fault is suspected. • The electrical plug must not be removed from the socket by pulling the cable. • Never immerse the iron or steam tank in water or any other fluid. • Do not leave the appliance exposed to weather conditions (rain, sun, frost, etc. ). [. . . ] • To avoid damage and/or contamination of the water tank and the boiler, do not put perfume, vinegar, starch, descaling agents, additives or any other type of chemical product into the water tank. Any damage caused by the use of the aforementioned products, will make the guarantee void. • The iron pad can be placed into the specially designed recess on the appliance or somewhere suitable alongside the ironing area. • During its first use the iron may produce certain vapours and odours, along with white particles on the soleplate, this is normal and it will stop after a few minutes • While the steam release button is pressed, the water tank may produce a pumping sound, this is normal, indicating that water is being pumped to the steam tank. 4. Unwind the mains cable (6) fully and plug it into an earthed socket. 6. The “Steam ready” indicator lamp (9) will light up after several minutes, indicating that the appliance is ready to use. When using the steam generator for the first time, or when using it straight after “Calc’nclean”, the steam generator will take slightly longer to heat up. The “refill water tank” indicator (11) will light when the water tank is empty. * model dependent  en Setting the temperature 1. Check the ironing instruction label on the garment to determine the correct ironing temperature. 2. Turn the temperature selector (14) to the required setting: • •• ••• 3. The indicator lamp (17) will remain lit while the iron is heating and go out as soon as the iron has reached the selected temperature. For normal use, please choose one of the following recommended settings: Temperature • Synthetics Silk – Wool Cotton – Linen 3. Press the steam release button (15 or 16*) to release steam. Steam setting •• ••• Tips: • Sort your garments out based on their cleaning symbol labels, always starting with clothes that have to be ironed at the lowest temperatures. • If you are not sure what the garment is made of then begin ironing at a low temperature and decide on the correct temperature by ironing a small section not usually seen when worn Attention: When ironing on a lower temperature setting “•”. • If the appliance has variable steam control (10*), set the variable steam control to its lowest position . • If the appliance does not have variable steam control, press the steam release button only for a few seconds at a time when ironing at lower temperatures. 3. If the soleplate is soiled with dirt or scale, clean it with a damp cotton cloth. 4. Never use abrasive products or solvents. Storing the appliance 1. Always allow the appliance to cool down before storing it. 2. Set the main power to the “0” position and disconnect the mains cable. * model dependent 5. Use the carrying handles (4) on the sides when moving the appliance. 4. Store the mains cable in the storage compartment (5) and the steam hose in the storage fixing (3). Do not wrap the cords too tight. 3. Place the iron on the iron pad, standing on the soleplate.  en “Calc‘n clean” Cleaning the Boiler To extend the life of your steam generator and to avoid any build up of scale, it is essential that you rinse out the boiler after several hours of use (approximately after 50 hours). Do not use descaling agents for rinsing out the boiler, as they could damage it. 1. Check that the appliance is cold and unplugged for more than 2 hours, and that the water tank (1) is empty. 2. Place your appliance on the edge of your kitchen sink, so that any residual water in the water tank is directed into the sink. 3. Remove the plastic cover located on the bottom of the appliance by turning it to the position. 4. Unscrew the boiler drainage plug using a coin. 5. Holding your steam generator in an upside down position, and using a jug, fill the boiler (in the base unit) with 1/4 litre of water 6. Shake the base unit for a few moments and then empty it completely over a sink or bucket. To obtain the best result, we recommend that this operation is done twice. Important: before closing, make sure no water remains in the boiler. [. . . ] Water drops stop coming out of the soleplate after using the “Ultimate steam”* function for some time. Ensure that the steam generator is positioned to the side of the hand you are using to iron, to reduce contact with the hose as much as possible. Tighten up boiler drainage plug with a coin Waterspots appear May be caused by steam on the garment during condensed on the ironing board. Water spots appear Water spots are caused by steam on the garment during condensation in the hose when use of the “Ultimate cooling down after use. [. . . ]