User manual BRANDT PRO251RC

[. . . ] EN 6 / AFTER-SALES SERVICE Any maintenance on your equipment should be undertaken by: - either your dealer, - or another qualified mechanic who is an authorized agent for the brand appliances. When making an appointment, state the full reference of your equipment (model, type and serial number). This information appears on the manufacturer's nameplate attached to your equipment. Tijdens het telefoneren, dient u de complete referentie op te geven van uw machine (model, type, serienummer). [. . . ] 4) Replace the rubber screw covers (they also serve to absorb the shock caused by closing the oven door). Tip To be certain that you have properly installed your appliance, do not hesitate to call on a household appliance specialist. Qxp 12/01/2007 15:14 Page 23 2 / INSTALLING YOUR APPLIANCE EN Monophase 20A Meter 220-240V~ 50Hz Monophase line 220-240 V ~ A fuse or differential circuit breaker Electrical outlet 2 prong receptacle + ground lead CEI Standard 60083 Power cable length 1. 50 m approximately • ELECTRICAL CONNECTION Electrical safety must be provided by a correct build-in. During build-in and maintenance operations, the appliance must be unplugged from the electrical grid; fuses must be cut off or removed. The electrical connections are made before the appliance is installed in its housing. Ensure that: - the electrical installation has sufficient voltage, -the electrical wires are in good condition - the diameter of the wires complies with the installation requirements. Your oven must be connected with a power cord (standardised) with three 1. 5 mm2 conductors (1 ph +1 N + ground) that must be connected to a monophase 220-240 V~ net23 work via a CEI 60083 standardised receptacle (1 ph +1 N + ground lead) or an all-pole cut-off device, in compliance with installation regulations. Warning The safety wire (green-yellow) is con nected to the appliance’s terminal and must be connected to the ground lead of the electrical set-up. In the case of a hook-up with electrical outlet, it must be accessible after installation. If the power cable is damaged, it must be replaced by a cable or a special kit available from the manufacturer or its After-Sales Service Department. Qxp 12/01/2007 15:14 Page 24 EN 2 / INSTALLING YOUR APPLIANCE Warning We cannot be held responsible for any accident resulting from an inexistent, defective or incorrect ground lead. If the electrical installation at your residence requires any changes in order to hook up your Appliance, call upon a professional electrician. If the oven malfunctions in any way, unplug the appliance or remove the fuse corresponding to the sector there the oven is hooked up. € CHANGING THE POWER CORD — The power cable (H05 RR-F, H05 RN-F ou H05 VV-F) must be of sufficient length to be connected to the build-in oven while it sits on the floor in front of the cabinet. To do this the appliance must be disconnected from the electrical network: — Open the inspection flap located at the lower right of the back cover by unscrewing the two screws, then pivot the inspection flap. € Loosen the screws from the terminal board and remove the power cord to be replaced. € Introduce the power cable through the side of the cover in the cable clip located to the right of the terminal board. € All the strands of the electricity wires must be captured under the screws. € The green-yellow coloured ground wire should be connected to the terminal . € Screw down tightly the screws on the terminal board and check the connection by pulling on each wire. [. . . ] ž Replace the fuse in your electrical set-up and check its capacity (16A). - The oven is not connected ➡ Plug in your oven or change the or the fuse is not working. - The fan should work for ➡ Open the oven door to accelerate 1 hour maximum after cook- the cooling down of the oven ing. - If it does not stop after 1 ➡ Call the After-Sales Service Departhour ment. [. . . ]