User manual BRANDT TI112B & TI112V,MV

[. . . ] Make sure that the power cable is not in contact with any heating zones. Qxd 18/10/02 10:36 Page 4 Installing your hob in complete safety Choice of installation Above a cupboard According to the layout of your kitchen, you should install your hob: 1 cm mini vide Gap sanitaire 4 cm CUPBOARD FRONT AVANT MEUBLE ;;; ;;; Above an oven The hob can be fitted directly into the worktop above an oven placed in its upper position (Minimum distance 10 mm). 58 51 4, 1 48, 8 56 The unit must be installed so that the mains plug is easily accessible. Fitting A seal exists for preventing any humidity getting under the hob. [. . . ] -Stick the seal under the rim of the hob and lower the hob into position on the worktop. -This seal is supplied in the sachet; stick it in place beneath the hob. 55, 5 49 4 min i 4m ini 21, 6 21, 6 4m ini dimensions in cm Screw the clips into position as shown below 4 Copie de 9962 5591. Qxd 18/10/02 10:36 Page 5 Installing your hob in complete safety Connection If the cable is damaged, it must be replaced by the manufacturers, their After Sales Service or another similarly qualified person for avoiding any possible risk of accident. When the power is switched on, or after a long power failure, a light code appears on the control panel. This disappears automatically after about 30 seconds or as soon as any touch control is touched on the panel. This is normal, as the display is for use by the after-sales service when required. If the unit has a 3 phase 400 V2N connection, and is not working correctly, check that the neutral wire is correctly connected. This precaution should also be taken for all your other electronic apparatus. 230V 400v 2N Your hob must be connected to the mains with: - A H05RRF type cable with three 2. 5 mm² conductors (including a yellow / green earth wire) 1 L1 2 3 N 4 1 2 3 L1 L2 - A plug that complies to CEI 83 recommendations or an all-pole circuit breaker with contacts that open by at least 3 mm. Under these conditions the temperature remains constant and is correctly adapted to the food you are cooking. minor troubleshooting IF YOU REALIZE THAT POSSIBLE CAUSES WHAT SHOULD YOU DO?When you switch on, the fuse blows When you switch on, only one side of the hob works Your hob is connected incorrectly Your hob is connected incorrectly The hob is working normally The apparatus is not under p o w e r . - Something has overflowed and or an object is touching the control panel. 8 Check the connection and make sure it complies with requirements. The display lights don't come on The hob has stopped during use and is giving out a bleep The display reads Message E NOTHING: see chapter Remarks on connections Inspect the fuses and the cut-out switch. Clean the hob or remove the object in question and start cooking again. Qxd 18/10/02 10:36 Page 9 Preserving and maintaining your hob ● You must: Avoid any shocks with recipients etc. As in time this will deteriorate the markings on the top of your ceramic hob. Avoid using recipients with rough or dinted bases: They may hold and transport matter liable to stain or scratch the hob. Any such faults, which are not the cause of breakdowns nor make the hob impossible to use, are not included in the guarantee conditions. [. . . ] Avoid using recipients with rough or dinted bases: They may hold and transport matter liable to stain or scratch the hob. Any such faults, which are not the cause of breakdowns nor make the hob impossible to use, are not included in the guarantee conditions. The diameter of the base must be as big as, or bigger than the cooking zone surface area marked on the ceramic plate. It is very easy to clean your countertop hob, especially if you follow these few recommendations: ● You must not Put plastic utensils on the cooking surface when it is hot. [. . . ]