User manual BRANDT VF400JU1

[. . . ] Contents Pages Installing your dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-36 Levelling by adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Anti-condensation protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Facing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Balancing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Building in and fixing the dishwasher . . . . . . . . . . . . . . . . . . . . . . . 32 Water connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Draining away the waste water. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35 Foam strip and soundproofing sea . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Installing the plastic corner brackets. . . . . . . . . . . . . . . . . . . . . . . . 36 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Building in under a hob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 30 EN Installing your dishwasher Remove the 2 red protective wedges from the front of your appliance to avoid causing a leak. Levelling by adjusting the feet Ensure that your dishwasher is well balanced and stable. The four feet can be adjusted, so adjust them if necessary using a screwdriver. If the feet are poorly adjusted, this decentres the door and makes your dishwasher wobble, causing leaks. [. . . ] If you use a selfpiercing tap, check that there is sufficient water flow. Check that the seal is fitted and that the connection is tight. If necessary, you can alter the hose's direction. To do this, loosen the connection at the bottom left on the rear of the machine and swivel it as necessary. For dishwashers fitted with safety hoses: You must remove the protective cover (see the drawing opposite) to alter the hose's direction. To do this, loosen the two screws (end fitting T20), remove the protective cover, position the connection in the direction you wish and then replace the protective cover. When you are making a new installation, you must use a new hose to connect the machine to the water supply: you must not re-use the old hose. 0, 1 - 1 MPa EN 33 Installing your dishwasher Draining away the waste water Length of the drain hose: standard 1. 50m. If necessary, you can increase the length of the drain hose (4m max. ). Connect the drain hose: - To a ventilated siphon For machines installed in columns, the height of the drain hose must not be higher than the top of the machine. NB: Pull the pipe gradually when installing it to avoid kinking it. - To a sink U-bend Remove the stopper form the U-bend. Remove the rubber stopper and, if necessary, add a collar. Electrical connection Mains voltage: 230V Fuse: 10A, 13A or 16A The socket outlet must be grounded to Earth. In all cases, the connection must comply with the standards in force in the country concerned, together with the supplementary regulations of the Electricity Authority. The machine must be switched off when the connection is made to the electrical circuit. We cannot be held liable for any damage caused by the faulty earthing of the machine. - Directly to your sink. Ensure that you hold your drain hose in place with the end connector to avoid flooding. If you have any doubts regarding the condition of your installation, do not hesitate to have it checked by a qualified electrician. The machine must be installed so that the socket remains accessible. 34 EN Installing your dishwasher Do not use an electrical extension, a double socket or an electrical timer. [. . . ] If the machine is operating incorrectly, disconnect it from the electricity supply (remove the plug) or switch off the circuit involved and close the water supply tap. If your dishwasher is being installed on a carpeted floor, make sure to adjust the feet to leave a ventilation space under the machine Building in under a hob If your worktop is fitted with a built-in hob over your dishwasher, you must provide thermal insulation on top of the machine. Take care to leave a space between the gas pipe and the top of your machine. [. . . ]