User manual BROTHER HL-1260E

[. . . ] Brother Laser Printer HL-1260e/HL-1660 USER'S GUIDE I Trademarks Brother is a registered trademark of Brother Industries, Ltd. Apple and LaserWriter are registered trademarks, and TrueType is a trademark of Apple Computer, Inc. EPSON is a registered trademark, and FX-850 and FX-80 are trademarks of Seiko Epson Corporation. Hewlett-Packard, HP and PCL are registered trademarks, and HP LaserJet 4+, HP LaserJet Plus, HP LaserJet II, HP LaserJet IID, HP LaserJet IIID, HP-GL, HPGL/2, and Bi-Tronics are trademarks of Hewlett-Packard Company. [. . . ] After you have finished sending data, press the SET switch again, so that the printer exits from the data reception status. When you exit from the data reception status, you see the following message on the display: DATA ID=##### Select the data ID with the v or w switch and press the SET switch. Notes · When you see an asterisk on the display, the ID number has been used for other data or a macro. If you select the used ID number, the old data or macro is erased and replaced with the new data. · Once the data is saved, you can execute it with "EXECUTE DATA" or with a data execution command. · The data saved in the SAVE DATA mode can not be run with the macro execution command in HP LaserJet 4+ emulation. 4­36 CHAPTER 4 CONTROL PANEL · Save Macro Note The "SAVE MACRO" menu appears only in the HP LaserJet 4+ emulation mode. If you have downloaded a macro in the printer's memory, you can save the macro on the installed flash memory card or HDD card. If a macro has been downloaded in the printer's memory and you press the SET switch at "SAVE MACRO, " the printer prompts you to select the ID of the macro. MACRO ID=##### Select the ID with the v or w switch and press the SET switch again, so that the printer saves the macro with the selected ID. Note When you see an asterisk on the display, the ID number has been used for another macro or data. If you select the used ID number, the old macro or data is erased and replaced with the new macro. You can execute a macro with the macro execution command. · Primary Font or Secondary Font Note The "PRIMARY FONT" and "SECONDARY FONT" menus appear only in the HP LaserJet 4+ emulation mode. If you have selected the primary or secondary font with the FONT switch, you can save the font on the installed flash memory card or HDD card. When you press the SET switch at "PRIMARY FONT" or "SECONDARY FONT, " the printer prompts you to select the ID of the font. FONT ID=##### 4­37 USER'S GUIDE Select the ID with the v or w switch and press the SET switch again, so that the printer saves the font with the selected ID. Note When you see an asterisk on the display, the ID number has been used for another font. If you select the used ID number, the old font is erased and replaced with the new one. Whatever font you have selected with the FONT switch, the printer saves the font as a bitmapped font as long as the print size is no more than 24 points, so that the printer can print it faster than when they are not saved. It is recommended that you save the scalable font you frequently use for faster printing. Since the flash memory card or the HDD card is in the upper card slot A of the printer and fonts stored in the card behave in the same way as they would if they were in a dedicated Font Card, you can select the saved fonts as "SLOTFONT A" with the FONT switch or the font selection command from your software. You can check the saved fonts by printing the list of fonts with the TEST switch. Notes When you save the primary or secondary font, note the following: · The font is temporarily stored in the RAM of the printer before it is saved on the card. If the font data exceeds the RAM capacity, a memory full error occurs. As not all the font data has been stored in RAM, you cannot save the font to the card. [. . . ] ", " (space)", "$", " / ", "+", and "%" can be accepted as bar code data. The bar code data automatically starts and ends with an asterisk " * " (start character and stop character). If the received data has an asterisk " * " at its beginning or end, the asterisk is regarded as a start character or stop character. · When Interleaved 2 of 5 is selected with the parameter "t1" or "T1": Ten numerical characters "0" to "9" can be accepted as bar code data. [. . . ]