User manual BROTHER HL-1650 NETWORK USER

[. . . ] Multi-Protocol Print Server NC-4100h USER'S GUIDE Please read this manual thoroughly before using the printer. You can print or view this manual from the CD-ROM at any time, please keep the CD-ROM in a convenient place for quick and easy reference at all times. i Trademarks Brother is a registered trademark of Brother Industries, Ltd. HP, HP/UX, JetDirect and JetAdmin are trademarks of Hewllet-Packard Company. DEC, DEC server, VMS, LAT, and ULTRIX are trademarks of Digital Equipment Corporation. [. . . ] Press INSERT to get a list of the queue server candidates and select the print server service name from step 11, Press ENTER. Press ESCAPE several times until you return to the Available Options menu. You may either turn the printer off and on again or you may down the print server in PCONSOLE as follows: · · In the Available Options menu, highlight Print Server Information, and press ENTER. Select the print server name (BRN_xxxxxx_P1 or BRO_xxxxxx_P1 if using a NC-2000 series print server) and press ENTER. If you have NetWare 4. 1x, highlight Information and Status and press ENTER, and then skip to the next bullet. If you have NetWare 3. xx or 2. xx: - Highlight Print Server Status/Control and press ENTER. This will force the print server to rescan the available file servers for new queue entries. Alternatively, use the BRCONFIG or TELNET command SET NETWARE RESCAN to make the print server rescan for file servers. · 6-13 CHAPTER 6 NOVELL NETWARE PRINTING Configuring the Brother Print Server (Queue Server Mode in NDS mode) using PCONSOLE and BRCONFIG 1. Make sure that you are logged in as ADMIN in NDS mode on the NetWare 4. 1x file server. Press INSERT and enter the Print Server Name Enter the NetWare print service name of the print server exactly as it appeared in the printer configuration page (the default name is BRN_xxxxxx_P1 or BRO_xxxxxx_P1 if you are using a NC-2000 series print server such as the NC2010h or the NC-2100h, where "xxxxxx" is the last six digits of the Ethernet address (MAC address), unless you changed the name to something else). You can find the NetWare print service name and MAC address by printing out the printer configuration page. Refer to the Quick Setup Guide for information on how to print the configuration page on your print server. Important: Do not assign a password to the print server or it will not log in. Press INSERT type in the desired print queue name (you will also be asked for a volume name. Press INSERT and select the appropriate volume), and press ESCAPE to return to the main menu. Select Print Servers and press ENTER to specify which network print servers can print jobs from this print queue. Press INSERT to get a list of the queue server candidates and select the NetWare print server name from step 4, which will then be added to the list. Select Print Servers and select the name of the printer server that you entered in Step 4. Press INSERT and select the name of the printers you entered in Step 12. Press ESCAPE several times to return to DOS. 6-14 CHAPTER 6 NOVELL NETWARE PRINTING 18. Execute the BRCONFIG from the Windows menu or insert the Brother Print Server Configuration Utility diskette in Drive A: of your PC and type: A:BRCONFIG. When you get the message that the print server is connected, press the ENTER key and type the default password of "access" in response to the "#" prompt (the password will not echo), and then press the ENTER key again in response to the ENTER Username> prompt. [. . . ] For which ever method you select, you must enter a password for the print server. TFTP PUT from this host Use this method if you have TCP/IP already installed on your PC. BRAdmin will use the TFTP protocol to send the new firmware data to the print server. TFTP GET from a server If you have a TFTP server installed in your network (many Unix systems provide TFTP support), you may wish to use this option. [. . . ]