User manual BROTHER HL-1670N

[. . . ] Laser Printer HL-1650/1670N Quick Setup Guide Read the "Safety Sheet" first to ensure that you use this printer safety. Read this "Quick Setup Guide" before you set up the printer. Before you can use the printer, you must set up the hardware and install the driver. [. . . ] You can easily access it and receive the latest drivers and information for this printer. Make Disk Sets (only for Windows®) 1 Press the cover release button, and then open the front cover. 2 Remove the protective part. 3 Unpack the drum unit assembly. Rock it from side to side 5 or 6 times to distribute the toner evenly inside the assembly. 4 Install the drum unit assembly into the printer. 5 Close the front cover. Step 3 Load paper into the paper cassette Paper guide release lever Universal guide release lever Up to here Paper cassette 1 Pull the paper cassette completely out of the printer. 2 While pressing the paper guide release lever, slide the adjusters to fit the paper size. paper, press the universal guide release lever as you extend the rear of the paper cassette. 3 Load paper into the paper cassette. Check that the paper is flat in the tray and below the maximum paper mark. 4 Re-install the paper cassette into the printer. Step 4 Print a test page O I Extend the tray extension flap READY Data Back Data Back PRINTING Reprint Reprint Set Go Job cancel Set Go O OFF ON I Job cancel OFF ON 1 Make sure the printer power switch is off. Do not connect the interface cable. 2 Plug the AC power cord into an AC outlet. Turn the power switch on. 3 After the printer has finished warming up, the READY message appears. 4 Press the Go switch. Note: When you want to set the control panel message language, refer to the control panel section on the reverse side of this sheet. ©2000 Brother Industries, Ltd. Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the U. S. Macintosh® and iMac® are registered trademarks of Apple Computer, Inc. All other brand and product names are trademarks or registered trademarks of their respective holders. Continue to the reverse side. Follow the instructions for your interface cable and operating system. For Parallel interface cable users (For Windows® users only) Step 5 Connect the printer to your PC & Install the printer driver O O I OFF ON OFF ON I 1 Click "Connect the interface cable and install the printer driver / utilities". 2 Select the parallel interface cable. 3 Turn the printer power switch off. 4 Connect the interface cable to your PC, and then connect it to the printer. 5 Turn the printer power switch on. Note: If "Add New Hardware Wizard" appears, click the Cancel button. 6 Click the Next button. 7 Click the Finish button. The setup is now complete. For USB interface cable users (For Windows® users only) Step 5 Install the driver & Connect the printer to your PC For USB interface cable users (For Macintosh® users only) Step 5 Install the Driver & Connect the Printer to your Macintosh® O I OFF ON Note: When the "Add New Hardware Wizard" appears on your PC, click the Cancel button. Note: Start installing the driver before you connect the USB interface cable to the printer. If you have already connected it, remove it. 1 Click "Connect the interface cable and install the printer driver / utilities". 2 Select the USB cable. 3 Click the Next button. 1 Double-click the Printer Driver Installer icon, and then follow the instructions on the screen. 2 Make sure the printer power switch is on. 3 Connect the USB interface cable to your Macintosh®, and then connect it to the printer. O I 4 OFF ON Open the Chooser from the Apple® menu on the Macintosh®. 5 Click the HL-1650/1670N icon and select it. [. . . ] (You can return to the READY status by pressing the Go switch. ) For more information, see Chapter 3 "CONTROL PANEL" in the User's Guide. For Network users If you want to connect your printer using a Network cable, refer to the Quick Network Setup Guide. After the administrator has made the required settings, install the driver referring to the "Installing the Driver for Network users" section of the Quick Network Setup Guide. For HL-1650 user: Install the optional Network board (NC-4100h) referring to Chapter 4 of the printer. [. . . ]