User manual BROTHER HL-2600CN

[. . . ] Brother Color Laser Printer HL-2600CN Series User's Guide Version 0 Before you can use the printer, you must set up the hardware and install the driver. Please read this manual thoroughly before using the printer and keep the CD-ROM in a convenient place for quick and easy reference at all times. Please visit our user support web site, Brother Solutions Center, at http://solutions. brother. com. You can download driver updates and product information. Trademarks Brother is a registered trademark of Brother Industries, Ltd. [. . . ] This could void your warranty. · Do not stand the toner cartridge on its end or turn it upside down. · Install the toner cartridges immediately after you remove the protective cover. 5-4 5-8 CHAPTER 5 MAINTENANCE OIIL BOTTLE L OTTLE Oil Bottle Low Message When the Oil has almost run out, the following message appears on the LCD panel. After this message appears, you can print approximately 30 pages: FUSER OIL LOW !" READY Oil Bottle Empty Message When the Oil completely runs out, the following message appears on the LCD panel and the printer stops printing. When you see this message, you must replace the Oil Bottle with a new one: OIL EMPTY Replace the oil bottle 5-9 CHAPTER 5 MAINTENANCE !Be sure to wait until the Fusing Unit has cooled sufficiently before you replace the Oil Bottle. If you touch the HOT parts (shaded area shown below), you might get injured. !If you spill some oil, consult your dealer or Brother authorized service representative. · Do not loose the Oil Bottle cap. It might cause the oil to leak. 5-10 CHAPTER 5 MAINTENANCE Replacing the Oil Bottle 1. Press the Power button to turn off the printer, and then wait until it has cooled down sufficiently. 2. Hold a sheet of paper under the Oil Bottle and lift it out of the Fusing Unit. Install the new Oil Bottle into the Fusing Unit with the label facing you. Press the Power button to turn the printer On. 5-12 CHAPTER 5 MAINTENANCE FUSER CLEANER USER LEANER Fuser Cleaner Message When the following message appears on the LCD panel, you will need a replacement Fuser Cleaner Roller: REPLACE FCR !" READY Fuser Cleaner Change Message When the following message appears on the LCD and the printer stops printing, you must replace the Fuser Cleaner: CHANGE FCR Replace the cleaning roller 5-13 CHAPTER 5 MAINTENANCE Replacing the Fuser Cleaner !Be sure to wait until the Fusing Unit has cooled sufficiently before replacing the Fuser Cleaner. 3. Press the Power button to turn the printer off, and then wait until it has cooled down sufficiently. 5-8 5-14 CHAPTER 5 MAINTENANCE 4. Take the Fuser Cleaner out of the Fusing Unit by holding the handle of the Fuser Cleaner as shown: Fig. 5-9 5. Install the new Fuser Cleaner into the guide with the roller side facing you. Fig. Press any of the Menu buttons (+, ­ , Set or Back) to take the printer Off Line. 10. Press Set to proceed to the next menu level, and then press + or ­ until "PARTS LIFE" appears. 12. The printer is now in the READY state. 5-15 CHAPTER 5 MAINTENANCE WASTE TONER PACK ASTE ONER ACK Approximately every 18, 000 images you print at 5% coverage, you must change the Waste Toner Pack. NEAR WASTE TONER !" READY Waste Toner Pack Full Message When the Waste Toner Pack is full, the following message appears on the LCD and the printer will stop printing. When you see this message, you must replace the Waste Toner Pack: WASTE TONER Replace the waste toner pack ! [. . . ] 8. Envelopes constructed of paper with a weight that exceeds the paper weight specifications for the printer. Poorly manufactured envelopes with edges that are not straight or consistently square. Envelopes with "baggy" construction or folds that are not sharply creased. Envelopes that do not lie flat or that are curled, wrinkled, or irregularly shaped. [. . . ]