User manual BROTHER HL-3260N

[. . . ] version C Brother Laser Printer HL-3260N USER'S GUIDE Please read this manual thoroughly before using the printer. Keep this manual in a convenient place for quick reference at all times. I Trademarks Brother is a registered trademark of Brother Industries, Ltd. Apple and LaserWriter are registered trademarks, and TrueType is a trademark of Apple Computer, Inc. EPSON is a registered trademark, and FX-850 and FX-80 are trademarks of Seiko Epson Corporation. [. . . ] Press the Set switch to enter the next lower menu level of the selected menu. IP ADDRESS= 192. 0. 0. 192 2: blinking The number that can be changed is blinking. Press the + or ­ switch to increase or decrease the number. IP ADDRESS= 123. 000. 000. 192 Press Set. IP ADDRESS= 123. 45. 67. 89 3-33 USER'S GUIDE ! About emulation modes This printer has the following emulation modes: " HP LaserJet Mode The HP LaserJet mode (or HP mode) is the emulation mode where this printer emulates the Hewlett-Packard LaserJet laser printer. A large number of software applications support this type of laser printer. Using this mode will allow your printer to operate at its optimum performance with these applications. " BR-Script 3 Mode BR-Script is a Brother original page description language and it is a PostScript® language emulation interpreter. The BR-Script interpreter of this printer can control text and graphics on pages completely and satisfactorily. If you want to obtain technical information about PostScript commands, see the following commercial manuals: · Adobe Systems Incorporated. Addison-Wesley Longman, Inc. , 1999. 3-34 CHAPTER 3 CONTROL PANEL " HP-GL Mode The HP-GL mode is the emulation mode where this printer emulates the Hewlett-Packard plotter model HP-7475A. Use this mode for optimum performance when printing from these types of applications "EPSON FX-850 and IBM Proprinter XL Mode The EPSON FX-850 and IBM Proprinter XL modes are the emulation modes that this printer emulates to meet the industry-standard for dot matrix printers of their respective manufacturers. Use these emulation modes for optimum performance when printing from those types of applications. 3-35 USER'S GUIDE ! List of Factory settings The following table shows the factory settings initially set before shipment. Notes · · The settings are subject to the emulation mode. The following settings cannot be restored to the factory settings with the RESET menu in the "FACTORY SETTINGS" mode: INTERFACE MODE, HRC SETTING, PAGE PROTECTION, SCALABLE FONT, LOCK PANEL, PAGE COUNTER and local language for display messages. The COPY setting is always restored to the factory setting when the printer is turned off and on again. If you need to reset the Network card, press the Test button on the rear of the Network board (NC-4100h) more than 5 seconds. MODE MODE MODE PAPER MENU MENU MENU SOURCE MP FIRST MP SIZE MANUAL FEED TRAY1 SIZE TRAY2 SIZE TRAY3 SIZE TRAY4 SIZE DUPLEX OUTPUT JOB OFFSET QUALITY RESOLUTION HRC TONER SAVE DENSITY SETUP LOWER LCD POWER SAVE AUTO CONTINUE LOCK PANEL REPRINT EMULATION KEEP PCL Facttorry Setttiiing Facto ry Settt n g Fac o y Se ng =AUTO =OFF =A4/LETTER =OFF =A4/LETTER =A4/LETTER =A4/LETTER =A4/LETTER =OFF =STANDARD =ON =600 =ON =OFF =0 =NONE =30M =OFF =OFF =ON =AUTO(EPSON) =OFF · · 3-36 CHAPTER 3 CONTROL PANEL MODE MODE MODE PRINT MENU MENU MENU MENU MEDIATYPE PAPER COPIES ORIENTATION PRINT POSITION AUTO FF TIME FF SUPPRESS HP LASERJET Facttorry Setttiiing Facto ry Settt n g Fac o y Se ng =PLAIN PAPER =A4/LETTER =1 =PORTRAIT X OFFSET=0 Y OFFSET=0 =5 =OFF FONT NO. FONT PITCH/POINT SYMBOL CHARACTER SET TABLE PRINT AUTO LF=OFF AUTO CR=OFF AUTO WRAP=OFF AUTO SKIP=ON LEFT MARGIN RIGHT MARGIN TOP MARGIN BOTTOM MARGIN LINES EPSON FX-850 FONT NO. FONT PITCH/POINT SYMBOL CHARACTER SET TABLE PRINT AUTO LF=OFF AUTO MASK=OFF LEFT MARGIN RIGHT MARGIN TOP MARGIN BOTTOM MARGIN LINES 3-37 USER'S GUIDE MODE MODE MODE MENU MENU MENU IBM PROPRINTER Facttorry Setttiiing Facto ry Settt n g Fac o y Se ng FONT NO. FONT PITCH/POINT SYMBOL CHARACTER SET TABLE PRINT AUTO LF=OFF AUTO CR=OFF AUTO MASK=OFF LEFT MARGIN RIGHT MARGIN TOP MARGIN BOTTOM MARGIN LINES HP-GL CHAR SET(STD) CHAR SET(ALT) PEN SIZE=## DOTS PEN GRAY=## #% BR-SCRIPT NETWORK TCP/IP NETWARE APPLETALK NETBEUI DLC/LLC BANYAN LAT NETBIOS/IP ENET ERROR PRINT=OFF APT=OFF TCP/IP ENABLE=ON IP METHOD=AUTO NETWARE ENABLE=ON NET FRAME=AUTO =ON =ON =ON =ON =ON =ON =AUTO 3-38 CHAPTER 4 OPTIONS 4 C H A PTER 4 O PTI O N S CHAPTER 4 OPTIONS 2SWLRQDO $. . HVVRULHV 7KLV SULQWHU KDV WKH IROORZLQJ RSWLRQDO D. . HVVRULHV <RX . DQ LQ. UHDVH WKH SULQWHU¶V . DSDELOLW\ ZLWK WKHVH LWHPV 2SWLRQV $ % & ' ( ) * + , [ VKHHWV SDSHU WUD\ VKHHWV SDSHU WUD\ 'XSOH[ XQLW 0XOWLSXUSRVH WUD\ )LQLVKHU6WDSOHU %ULGJH 8QLW 0DLO %R[ , QWHU. KDQJH XQLW +DUG 'LVN 'ULYH /7 /7 '; 03 )6 %8 0; 63 +'*+'(; $ % C D E F Fig. 4-1 G H 4-1 Installing Options ! Caution · · · Before installing options, the machine should be turned off and unplugged for at least thirty minutes. Components inside the machine become very hot, and can cause a burn injury if touched. When lifting the machine, use the handholds on both sides of the printer to prevent damage to the machine or injury. 5 6 7 2 3 4 1 1 2 Fig. DC 24V. 4-2 CHAPTER 4 OPTIONS Option Installation Sequence When you install options, they should be installed in the sequence described below. 1. Installing Finisher/Stapler (FS- 5050) There are two types of paper trays: A 500x2 sheets paper tray (LT-5100) and a 2000 sheets paper tray (LT-5200) Only one of them can be installed at any time. [. . . ] (2) 6 digits The first character and the last check digit are removed from the 8 digit data. *1: For 8 digits, "?" can be used in place of a check digit. *2: Adding "+" and 2- or 5-digit number after the data creates an add-on code for all 6 and 8 digit formats. · When Codabar is selected with the parameter "t9" or "T9": Characters "0" to "9", "-", " . [. . . ]