User manual BROTHER HL-6050DN

[. . . ] Before replacing internal parts, cleaning the printer or clearing a paper jam, make sure you have turned OFF the power switch and unplugged the AC power cord from the AC power outlet/socket. Do not handle the plug or AC power cord with wet hands. This constitutes an electric shock hazard. After you have just used the printer, some internal parts of the printer are extremely hot. When you open the front cover or back cover of the printer, never touch the shaded parts shown in the illustration. Inside the printer (Front View) Open the Back Output Tray (Back View) The fuser unit is marked with a caution label. Please do Not remove or damage the label. 2 Regulations Federal Communications Commission (FCC) Declaration of Conformity (For USA) Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard P. O. [. . . ] Connecting the interface cable is done when installing the driver. 1 Insert the CD-ROM into your CD-ROM drive. Follow the on-screen instructions. 1 Insert the CD-ROM into your CD-ROM drive. Follow the on-screen instructions. 2 Click Initial Setup on the menu screen. 3 2 You can view the Initial Setup instructions and follow the steps on pages 9 to 12. Click Initial Setup on the menu screen. 3 You can view the Initial Setup instructions and follow the steps on pages 9 to 12. 8 2 Install the Drum Unit Assembly Do NOT connect the interface cable. You will be prompted to connect the interface cable during the driver installation. 3 Put the drum unit assembly into the printer. 1 Open the front cover by pressing the front cover release button. Windows® Parallel Front cover release button 4 Close the front cover of the printer. Installing the Driver Windows® Network For Administrators Macintosh® Network Macintosh® USB Front cover 2 Unpack the drum unit assembly. Rock it from side to side several times to distribute the toner evenly inside the assembly. Go to the next page 9 Windows® USB Setting Up Your Printer Step 1 1 Setting Up Your Printer 3 To avoid paper jams and misfeeds, fill the paper tray with small stacks of paper that you have fanned well. 3 Load Paper in the Paper Tray Pull the paper tray completely out of the printer. 4 2 While pressing the paper guide release lever, slide the adjusters to fit the paper size. Check that the guides are firmly in the slots. Put paper in the paper tray. Check that the paper is flat in the tray and below the maximum paper mark. Up to here Paper guide release lever 5 For Legal size paper, press the universal guide release button and pull out the back of the paper tray. Universal guide release button Put the paper tray firmly back in the printer. 10 4 Print a Test Page Do NOT connect the interface cable. Connecting the interface cable is done when installing the driver. 3 After the printer has finished warming up, the READY message appears. 1 Make sure that the printer's power switch is off. Check that the test page has printed correctly. Installing the Driver 2 Plug the AC power cord into an AC power outlet/socket. Turn the printer's power switch on. Go to the next page 11 For Administrators Macintosh® Network Macintosh® USB Windows® Network Windows® Parallel 4 Windows® USB Setting Up Your Printer Step 1 Setting Up Your Printer 6 Setting Your Language on the Control Panel 1 Press the + button until SETUP is displayed. Press the Set button. SETUP 2 Press the Set button again. LANGUAGE 3 Press the + or ­ button to select your language. Select Local Printer, and then click the Next button. 8 Click the Next button. Follow the on-screen instructions. A Select the port that your printer is connected to, and then click the Next button. 9 Select Standard Installation, and then click the Next button. B Click the Finish button. If you want to install the PS driver, select Custom and then follow the on-screen instructions. When the Select Components screen appears, check PS Printer Driver, and then continue following the on-screen instructions. If you do not want to install the User's Guide, select Custom and then follow the on-screen instructions. When the Select Components screen appears, remove the check from the User's Guide box, and then continue following the on-screen instructions. If you want to register your product on-line, check On-Line Registration. Setup is now complete. 18 For Brother Peer-to-Peer Network Printer Users (LPR / NetBIOS) If you are going to connect the printer to your network, we recommended that you contact your system administrator prior to installation. Before installation, if you are using Personal Firewall software (e. g. the Internet Connection Firewall available in Windows XP), disable it. Once you are sure that you can print, re-start your Personal Firewall software. Connecting the Printer to Your Network and Installing the Driver 1 Installing the Driver 19 2 Select the Network interface. 5 Turn on the printer's power switch. 3 Turn off the printer's power switch. 6 Click the Next button when the movie finishes. Continue to the next page For Administrators Windows® Network Windows® Parallel Click Connect the interface cable & Install the driver/utility from the Initial Setup menu. 4 Connect the network interface cable to the printer, and then connect it to a free port on your hub. Setting Up Your Printer For Network Interface Cable Users (For HL-6050DNDNDN) Step 2 7 Installing the Driver 0 For Network Interface Cable Users (For HL-6050DNDNDN) Click the Install button. Select Brother Peer-to-Peer Network Printer, and then click the Next button. 8 Click the Next button. Follow the on-screen instructions. A For LPR Users: Select Search the network for devices and choose from a list of discovered divices (Recommended). For NetBIOS Users: Select Search the network for devices and choose from a list of discovered divices (Recommended). [. . . ] Network User's Guide Chapter 7. 5 Double-click the PPD Installer icon to install the PPD file. Follow the on-screen instructions. Setup is now complete. 29 For Administrators Macintosh® Network Macintosh® USB Insert the CD-ROM for Macintosh® into your CD-ROM drive. Open your langauge folder. *1 If the Apple LaserWriter 8 Driver is not already installed on your system, you can download it from http://www. apple. com Installing the Driver Setting Up Your Printer Step 2 Installing the Driver For Network Interface Cable Users (For HL-6050DNDNDN) For Mac OS® X 10. 1 / 10. 2 Users Connecting the Printer to your Macintosh® & Installing the PPD File 1 Click Connect the interface cable & Install the driver/utility from the Initial Setup menu. 5 Turn on the printer's power switch. 2 6 Select the Network interface. Click the Install button and follow the onscreen instructions. 3 Turn off the printer's power switch. 7 From the Go menu, select Applications. 8 4 Connect the network interface cable to the printer, and then connect it to a free port on your hub. Open the Utilities folder. 30 I 9 Open the Print Center icon. If there is more than one of the same model printer (HL6050DN) connected on your network, the Ethernet address (MAC address) will be displayed after the model name. B 0 Click the Add Printer. . . button. Select BRN_xxxxxx_P1_AT*1, and then click the Add button. *1 xxxxxx are the last six digits of the Ethernet address. A Select AppleTalk. Network User's Guide Chapter 7. C From the Print Center menu, select Quit Print Center. For Mac OS® X 10. 2. 4 or greater Users: If you want to connect your printer using the Simple Network Configuration capabilities of Apple® Mac OS® X, select Rendezvous and then the HL-6050DNDND_DN series. [. . . ]