User manual BROTHER MW-140BT

[. . . ] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] (The User's Guide can be viewed by clicking the View User Guide button in the first dialog box that appears when the installer is started up to install the software. ) Note: Read the User's Guide before operating the printer. It is recommended you save the User's Guide onto your PC for future reference. Continued on the following page 1-4 4 Install the software according to the instructions that appear. To view the Software Guide, click the View Software Guide button. 5 Print!! Refer to the Software Guide. Note: Adobe Acrobat Reader is needed in order to view the User's Guide and the Software Guide. 1-5 Communication using Bluetooth technology In order for this printer to communicate using Bluetooth technology with the computer running Windows® or the Pocket PC, various Bluetooth settings must be specified. The following instructions show you the basic procedures for make a Bluetooth communication. For details, refer to the instruction manual for your Bluetooth device. 1 Set the MW-140BT the Bluetooth switch to ON. Bluetooth communication ON The status indicator light will be blue. 2 Run the Bluetooth connection software on the computer running Windows® or the Pocket PC. 3 The computer running Windows® or the Pocket PC searches for Bluetooth devices and the printer is detected. "MW-140BTxxxx" is detected. "xxxx" is a last 4 digit of its serial number. 4 Select this printer from the list of devices. The screen to enter the "PIN code" (or "Pass key") will appear. Only the first time that the computer running Windows® or the Pocket PC is connected to the printer will this screen appear. 1-6 5 Enter the "PIN code" (or "Pass key"), into the computer or Pocket PC and click/tap the enter button. The time of shipment, the PIN code is set to the last four digits of the serial number of the printer. "Connected device Yes" appears on the Device information screen. 6 Click/tap Connect Serial Port in the Operations menu. "Connected to serial port" appears on the Device information screen. Note the COM port number when it appears (The COM port number may be required when printing depending on the type of the computer or the pocket PC). 1-7 Product specifications Printer specifications Status indicator light (blue/green/red) Charging indicator light (orange) Method Direct thermal printing with a line thermal print head Resolution 300 dpi × 300 dpi 15 seconds/sheet Print speed (standard text on thermal paper with 7 % coverage at an ambient temperature of 74. 6 °F / 25 °C) 100 or more during continuous printing with a fully No. (Based on 7% coverage at an can be ambient temperature of 74. 6 °F / 25 °C) (Stanprinted dard paper manufactured by Brother: A7 thermal) Paper supply Brother paper cassette, automatic paper method feed mechanism Paper Brother A7 cut paper (2. 9" (74 mm) × 4. 1" (105 mm)) Compact switching AC adapter for charging, Power supply lithium ion battery (built in) 780 mAh (7. 4 V) Complies with USB Ver. 1. 1 class 2 serial port profile supported 3. 9" (100 mm) (W) × 6. 3" (160 mm) (not Dimensions including projection) (D) × 0. 7" (17. 5 mm) (H) 0. 66 lbs. (300 g) (including the built-in lithium Weight ion battery and a paper cassette containing 50 sheets of plain thermal paper) Indicators MW-140BT Accessories A7 size: 2. 9" (74 mm) × 4. 1" (105 mm) (2. 7" (69 mm) × 3. 9" (100 mm)) Label sheets 2. 9" (74 mm) × 1. 0" (26. 25 mm) (four down) (2. 7" (69 mm) × 0. 8" (21. 25 mm)) Label sheets 2. 9" (74 mm) × 2. 1" (52. 5 mm) (two down) (2. 7" (69 mm) × 1. 9" (47. 5 mm)) Count: 50 sheets/cassette (thermal paper) 30 sheets/cassette (all others) Normal type 1-8 Printing Español Declaración de conformidad de la Federal Communications Commission (Comisión federal de comunicaciones, FCC) (sólo para Estados Unidos) Parte responsable : Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA TEL: (908) 704-1700 declara que el producto Nombre del producto : MPrint MW-140 de Brother Número de modelo : MW-140 cumple con la Parte 15 de las Normas de la FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) este dispositivo no puede causar interferencias perjudiciales, y (2) este dispositivo debe aceptar cualquier interferencia que reciba, que incluye interferencias que puedan causar un funcionamiento no deseado. Este equipo se ha comprobado y cumple los límites establecidos para un dispositivo digital de clase B, conforme a la Parte 15 de la normativa de la FCC. Estos límites se han diseñado para proporcionar una protección razonable contra las interferencias indeseables en una instalación doméstica. Este equipo genera, utiliza y puede emitir energía de radiofrecuencia y, si no se instala y se usa según las instrucciones, puede causar interferencias perjudiciales a las comunicaciones de radio. No obstante, no se garantiza que no se producirán interferencias en una instalación específica. Si este equipo causara interferencias perjudiciales en la recepción de radio o de televisión, lo cual se puede comprobar apagando y encendiendo el dispositivo, el usuario puede corregir la interferencia llevando a cabo una o más de las medidas siguientes: -Volver a orientar o cambiar de sitio la antena de recepción -Aumentar la separación entre el equipo y el receptor. [. . . ] Inserte el disco compacto adjunto en la unidad de CD-ROM del PC con Windows®. 2 El instalador se inicia automáticamente y aparece el cuadro de diálogo Brother Mobile Printing Software. Si el instalador no se inicia automáticamente, haga doble clic sobre "Mi PC", y luego otro doble clic sobre . Disco compacto adjunto PC con Windows® PC de bolsillo Prepare la impresora. 3 Consulte la Guía del usuario. (La Guía del usuario puede verse haciendo clic en el botón que indica Guía del hardware del primer cuadro de diálogo que aparece cuando se inicia el instalador del software. ) Nota: Lea la Guía del usuario antes de poner en funcionamiento la impresora. [. . . ]