User manual BROTHER NETWORK PRINT SERVER

[. . . ] Multi-Protocol On-board Ethernet Multi-function Print Server and Wireless (IEEE 802. 11b/g) Ethernet Multi-function Print Server NETWORK USER'S GUIDE Please read this manual thoroughly before using this machine on your network. You can print or view this manual from the CD-ROM at any time, please keep the CD-ROM in a convenient place for quick and easy reference at all times. The Brother Solutions Center (http://solutions. brother. com) is your one stop resource for all your printing needs. Download the latest drivers and utilities for your machine, read FAQs and troubleshooting tips or learn about special printing solutions. Version 0 ENG Definitions of warnings, cautions, and notes We use the following icon throughout this User's Guide: Notes tell you how you should respond to a situation that may arise or give tips about how the operation works with other features. Trademarks Brother and the Brother logo are registered trademarks and BRAdmin Professional is a trademark of Brother Industries, Ltd. [. . . ] Go to step p. 5 Note · If you want to set more than one WEP key, click Advanced. · If you do not know the Authentication or Encryption settings for network, contact your network administrator. o Enter a new SSID name and choose the Authentication Method and Encryption Mode from the pulldowns in each setting box. Then enter the Network key and click Next. Note If you do not know the Authentication or Encryption settings for network, contact your network administrator. 79 Wireless Configuration for Macintosh® p Click Next. The settings will remain unchanged if you click Cancel. 5 Note If you want to manually enter the IP address settings of your machine, click Change IP Address and enter the necessary IP address settings for your network. q To communicate with the configured wireless device, you must configure your computer to use same wireless settings. Manually change the wireless settings on your computer to match the machine's wireless settings shown on this screen. Your settings will not be the same. ) 80 Wireless Configuration for Macintosh® r You have completed the wireless setup. If you would like to continue installing drivers and software necessary for operating your device, please select Start Here OSX from CD-ROM menu. 5 81 6 Control panel setup 6 LAN menu Before using your Brother product in a network environment, you need to configure the correct TCP/IP settings. In this chapter, you will learn how to configure the network settings using the control panel, located on the front of the machine. The LAN menu selections of the control panel allow you to set up the Brother machine for your network configuration. Please note that the machine is supplied with the BRAdmin Light Windows® software and Remote Setup applications for Windows® and Macintosh®, which also can be used to configure many aspects of the network. See Using the Remote Setup to change the print server settings (Not available for DCP models) on page 16 a for wired connection or Changing the print server settings on page 26 for a wireless connection. 6 6 Wired LAN TCP/IP / WLAN TCP/IP If you connect the machine with the Ethernet cable to your network, use the Wired LAN menu selections. If you connect the machine to a wireless Ethernet network, use the WLAN menu selections. This menu has nine sections: BOOT Method, IP Address, Subnet Mask, Gateway, Node Name, WINS Config, WINS Server, DNS Server and APIPA. 6 BOOT Method This selection controls how the machine obtains an IP address. Note If you do not want your print server configured via DHCP, BOOTP or RARP, you must set the BOOT Method to Static so that the print server has a static IP address. This will prevent the print server from trying to obtain an IP address from any of these systems. To change the BOOT Method, use the machine's control panel, BRAdmin Light utility or Remote Setup. 6 a b c d Press Menu. Press OK. 82 Control panel setup e f g Press a or b to select BOOT Method. Press Stop/Exit. 6 Auto mode In this mode, the machine will scan the network for a DHCP server, if it can find one, and if the DHCP server is configured to allocate an IP address to the machine, then the IP address supplied by the DHCP server will be used. If no DHCP server is available, then the machine will scan for a BOOTP server. If a BOOTP server is available, and it is configured correctly, the machine will take its IP address from the BOOTP server. If a BOOTP server is not available, the machine will scan for a RARP server. If a RARP server also does not answer, the IP Address is scanned through APIPA facility, see Using APIPA to configure the IP address on page 114. [. . . ] 24, 41, 68, 90 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Shared key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]