User manual CANON EOS REBEL T1I BROCHURE

[. . . ] If the camera or memory card is faulty and the images cannot be recorded or read by a personal computer, Canon cannot be held liable for any loss or inconvenience caused. Copyrights Copyright laws in your country may prohibit the use of images of people and certain subjects for anything but private enjoyment. Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Macintosh is a registered trademark of Apple Corporation in the United States and other countries. All other corporate names and trademarks mentioned in this manual are the property of their respective owners. [. . . ] If you press the <I> button to try and take a ninth spot meter reading, no spot meter reading will register. The exposure setting obtained with multi-spot meter readings will be canceled in the following cases: (1) After taking the last spot meter reading, 16 seconds elapse. Multi-spot metering can be fixed at the center or linked to the active AF point. 97 d Program AE 1 Select <d> on the LCD panel. Hold down the <W> button and turn the <6> dial to select <d>. Look through the viewfinder and aim the Area AF ellipse over the subject. The AF point which achieves focus flashes briefly and the focus confirmation light <o> in the viewfinder lights at the same time. The exposure setting will be displayed on the LCD panel and in the viewfinder. the display. 3 Checkshutter speed and aperture value The will be set automatically and displayed in the viewfinder and on the LCD panel. As long as the shutter speed and aperture value are not blinking, the exposure will be correct. 4 Take the picture. and press the Compose the shot shutter button completely. 98 d Program AE If "30" and the maximum aperture blink, it indicates underexposure. If "8000" and the minimum aperture blink, it indicates overexposure. If automatic AF point selection (p. 82) has been set, all the AF points that achieve focus will light. Or decrease the ISO speed. Aperture Value Display The larger the f/number, the smaller the aperture opening will be. If no lens is attached to the camera, "00" will be displayed for the aperture value. Depth-of-field Preview Press the depth-of-field preview button to stop down to the current aperture setting. The diaphragm in the lens will be set to the current aperture so you can check the depth of field (range of acceptable focus) through the viewfinder. The exposure will be locked (AE lock) while you press the depth-of-field preview button. 103 a Manual Exposure In this mode, you set both the shutter speed and aperture value as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a handheld exposure meter. *a stands for Manual. 1 Select <a> on the LCD panel. Hold down the <W> button and turn the <6> dial to select <a>. Then let go of the button. 2 Turn the <7> switch to <1>. <6> dial to 3 Turn thespeed and turnset the shutter the <5> dial to set the aperture. To set the aperture, you can also press the <O> button and turn the <6> dial. 4 Focus the subject. On the right of the viewfinder, the exposure level indicator <s> indicates the current exposure level relative to the standard exposure index <a>. 104 a Manual Exposure Exposure level indicator the 5 SetCheckexposure. level and set the the exposure desired shutter speed and aperture value. 6 Take the picture. 105 OSetting Exposure Compensation Exposure compensation is used to alter the standard exposure setting set by the camera. You can make the image look lighter (increased exposure) or darker (decreased exposure). The exposure compensation amount can be set up to ±3 stops in 1/3-stop increments. First set the <7> switch to <1>. 1 Press the shutter button halfway. (9) Check the exposure level. Turn the <5> dial to set the 2 desired exposure compensation amount. The exposure level indicator <N> is displayed on the LCD panel, and the exposure compensation icon <y> and the exposure level indicator <s> are displayed in the viewfinder. [. . . ] -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. The cable with the ferrite core provided with the digital camera must be used with this equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. [. . . ]