User manual CANON PIXMA MP530

[. . . ] Office All-in-One User's Guide ENG QT5-0210-V02 Getting Help from Canon Help Us Help You Better Before you contact Canon, please record the following information. Serial Number (located on the inside of the product): ____________________ Model Number (located on the front of the product): _____________________ Setup CD-ROM number (located on the CD-ROM): _____________________ Purchase Date: __________________________________________________ Customer Technical Support Sequence* 1. Internet -- www. canontechsupport. com For quick and comprehensive self-help in an intuitively guided interactive troubleshooting environment, the place to start is our helpful tech support web site. In addition, the latest driver downloads, answers to frequently asked questions, product information, and "where to buy" instructions are found here. 2. Email Tech Support -- www. canontechsupport. com For individual attention to a special issue, try emailing our friendly technical support representatives, specially trained to communicate quick, easy, and logical solutions to your inquiries within 24 hours. 3. [. . . ] MARK: OFFHOOK ALARM Enables/disables the alarm that alerts you if the handset of the telephone connected to the machine is not hung up properly. VOLUME CONTROL Sets the RX RING VOLUME and LINE MONITOR VOL. RX RING VOLUME: LINE MONITOR VOL. : When the machine is set to ring, selects the ring volume. Selects the line monitor volume while dialing. RX RING LEVEL Selects the ring type for incoming call. TEL LINE TYPE Selects the telephone line type setting for your machine. Note In New Zealand, select <TOUCH TONE>. You cannot use <ROTARY PULSE>. ACTIVITY REPORT Sets whether to print the ACTIVITY REPORT automatically after every 20 transactions. TX SETTINGS ECM TX 94 Changing the Machine Settings Chapter 7 Enables/disables Error Correction Mode (ECM) sending. PAUSE TIME Selects the pause length when you press [Redial/Pause]. AUTO REDIAL Enables/disables automatic redialing. REDIAL TIMES: REDIAL INTERVAL: If you select <ON> as <AUTO REDIAL>, enables setting the number of redialings. If you select <ON> as <AUTO REDIAL>, enables setting the length of time between redialings. TX START SPEED Selects the speed at which the machine starts transmitting. COLOR TX When faxing in color from the ADF, enables/disables automatic converting the image into black and white before sending if the destination fax device does not support color. TX REPORT Enables/disables automatic printing of a transmission report after sending. ATTACH TX IMAGE: If you select <PRINT ERROR ONLY> or <PRNT FOR EACH TX> as <TX REPORT>, enables/disables printing the first page of the fax under the report (black & white faxes only). DIAL TONE DETECT If you selects <ON>, the machine transmits after confirming the dial tone. This function may not be supported depending on your country or area. RX SETTINGS ECM RX Enables/disables Error Correction Mode (ECM) during reception. FAX/TEL AUTO SW If you select <FAX/TEL AUTO SW> as the receive mode, customizes its settings. RING START TIME: TEL RING TIME: DEFAULT ACTION: Selects the time the machine takes to check whether a call is a fax or voice call. Selects whether the machine switches to receive mode after the ring time has elapsed, or whether it disconnects the call. DRPD:FAX RNG PAT If you select <DRPD> as the receive mode, select the ring pattern for the machine. This setting is only available in US and Canada. INCOMING RING If you select <FAX/TEL AUTO SW>, <DRPD> or <FAX ONLY MODE> as the receive mode, enables/disables ringing for fax calls (A telephone must be connected to your machine for ringing to occur). RING COUNT: If you select <ON> as <INCOMING RING>, selects the number of rings for fax calls. Chapter 7 Changing the Machine Settings 95 MAN/AUTO SWITCH If you select <MANUAL MODE> or <ANS. MACHINE MODE> as the receive mode, enables/disables the machine to switch to fax receive mode after ringing for a specified length of time. RX START TIME: Selects the length of time the machine rings before switching to fax receive mode. REMOTE RX Enables/disables remote receiving. If you select <ON>, selects the remote receiving ID. RX IMG REDUCTION Enables/disables automatic reduction of faxes to fit the paper loaded. DIRECTION: If you select <ON> as <RX IMG REDUCTION>, enables selecting the direction of the reduction. RX START SPEED Selects the speed at which the machine starts receiving. RX REPORT Enables/disables automatic printing of a reception report after receiving. If you select <PRINT ERROR ONLY> or <PRINT FOR EACH RX>, prints a reception report only when a print error occurred or every time you receive a fax. OTHERS AUDIBLE TONES Selects the volume. KEYPAD VOLUME Selects the beep volume when pressing the buttons on the Operation Panel. ALARM VOLUME Selects the alarm volume. PWR SAVE SETTING Specifies the time to switch the machine to the Power Saver mode. COUNTRY SELECT Selects the country where you are using your machine. This setting is not available in some countries and regions. LANGUAGE SETTING Selects the language for LCD messages. RESTORE DEFAULT You can change the settings back to the settings on your purchase (some data may not be reset depending on your usage condition). 96 Changing the Machine Settings Chapter 7 SAVE CONFIG Saves the settings for the Settings screen. LOAD CONFIG Loads the settings for the Settings screen that were saved. Chapter 7 Changing the Machine Settings 97 Chapter 8 Routine Maintenance Replacing an Ink Tank When ink runs out, replace the ink tank. The machine will not print if the wrong type of ink tank is used, or if it is installed in the incorrect position. Black: CLI-8BK Magenta: CLI-8M Black: PGI-5BK Cyan: CLI-8C Yellow: CLI-8Y Note Be sure to install the ink tanks in the correct order. The proper arrangement from the left is Black , Black , Yellow , Magenta , Cyan . Should missing characters or white streaks appear despite sufficient ink levels, see "When Printing Becomes Faint or Colors are Incorrect" on page 103. Getting the Ink Level Information You can check the ink tank status by the ink lamp display. [. . . ] Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. Telepermitted equipment only may be connected to the auxiliary telephone port. The auxiliary telephone port is not specifically designed for 3-wire-connected equipment. 3-wire-connected equipment might not respond to incoming ringing when attached to this port. [. . . ]