User manual CARVIN RX1200R

[. . . ] CARVIN ENGINEERING DATA RX1200L, RX1200R MIXERS OPERATING MANUAL RX1200L with end caps removed for rack mounting -orRX1200R these mixers is the "SMT" Surface Mount Technology that utilizes surface mounted components to prevent parts from shaking or vibrating loose. Precision 1% tolerances guarantee that your settings will be accurate every time. Fire retardant FR-4 military spec circuit boards feature double-sided copper construction to guard against noise and radio frequencies (RF). RX1200L RX1200L in RW5 Road Warrior Case 20. 5"W x10"H x 12. 75"D(without lids) RX1200L in RW6 Road Warrior Case with two USM16 wireless receivers 20. 75"W x 12"H x 18"D(without lids) RECEIVING INSPECTION--read before getting started INSPECT YOUR AMP FOR DAMAGE which may have occurred during shipping. [. . . ] Refer to replacement text on the unit for correct fuse type. SERVICE: In the USA, please go to www. carvinservice. com Outside the USA, contact your dealer or go to http://www. carvinworld. com for your nearest service center. Include a written decription of the problem with serial numbeer and date of purchase. MAINTAINING YOUR EQUIPMENT Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of your unit can be wiped from time to time with a dry or slightly damp cloth in order to remove dust and bring back the new look. As with all pro gear, avoid prolonged use in caustic environments (salt air). When used in such an environment, be sure the mixer is adequately protected by a cover. SAFETY INSTRUCTIONS (EUROPEAN) The conductors in the AC power cord are colored in accordance with the following code. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAIN PLUG INTO A POWER SOCKET. CAUTION RISK OF ELECTRIC SHOCK REFER SERVICING TO QUALIFIED SERVICE PERSONNEL!THIS UNIT CONTAINS HIGH VOLTAGE INSIDE! 12340 World Trade Drive, San Diego, CA 92128 www. carvin. com RX1200L, RX1200R CONTROLS QUICK START UP 12. MONITOR 1& MONITOR 2 LEVELS If you're like most new owners, you're probably in a hurry to The EFF 1 and EFF 2 controls adjust the levels sent to the (AMPS 3&4) 7. With the mixer unplugged and the unit turned off, complete the following procedures: dual effects processors and to the EFF 1 and EFF 2 SND jacks. The effects controls are post-channel level and automatically track the channel's LEVEL & tone controls. Reduce these levels if PEAK LEDs are flashing on the effects processors. The MONITOR 1 and MONITOR 2 levels are sent to the GRAPHIC EQs which feed the AMPS 3 & 4, and the MONITOR 1&2 output jacks. 19. SUB X-OVER SWITCH The SUB XOVER (crossover) switch removes all frequencies above 120Hz for connecting the MONO(SUB) output to an amplified subwoofer. PHANTOM POWER SWITCH AND LED The PHANTOM PWR switch turns on the microphone phantom power in the channel XLR jacks. Note: Make sure the phantom power is switched off before connecting or disconnecting microphones to the mixer. A. CONNECTING AC POWER TO YOUR MIXER · Be sure to plug your mixer into the proper voltage, either 120V or 240V, 50Hz or 60Hz. · Use only a grounded (3 prong) power outlet to prevent a shock hazard. CONNECTING INPUTS TO YOUR MIXER · For balanced microphones, use a shielded cable and plug into the XLR MIC inputs. · For high output devices like instruments & keyboards, plug into the LINE input jacks using a shielded cable. The purpose for this is the monitor mix adjustments can be made without disturbing the main mix. ered from this position, they boost or cut respectively a narrow frequency band. To reduce feedback in the low frequency range, try lowering one of the 80 or 160 Hz sliders. [. . . ] Note: Make sure the phantom power is switched off before connecting or disconnecting microphones to the mixer. 4. CHANNEL LEVEL CONTROL The LEVEL control adjusts the volume of the channel before going to the PAN control. Here is where the individual channel volumes are adjusted to make up the overall mix at the MAIN L/R outputs. TAPE OUT JACKS The L-R TAPE OUT RCA jacks send the MAIN L/R signals (pre graphic EQ) for recording. [. . . ]