User manual CAT EYE CC-8000

[. . . ] Attn : CAT EYE Customer Service Section. #169-6660 Bracket Kit Kit support d'unite principale Halterung Bracketkit Kit supporto Soporte #169-6670 Cordless Sensor Palpeur (Emetteur) Sensor mit Sender Sensor-draadloos Sensore"Senzafilo" Sensor sin cable BEGRENZTE GARANTIE 2-Jahres-Garantie: Auf den Computer und den Sensor Falls während des normalen Gebrauchs Fehler auftreten, wird das entsprechende Teil kostenlos repariert oder ersetzt. durchgeführt werden, und das zu reparierende Produkt muß direkt durch den Händler an CAT EYE Co. , Ltd. Bei der Rückgabe des Gerätes zur Reparatur packen Sie es sorgfältig anbei. Achten Sie darauf, Ihren Namen und Ihre Anschrift klar und deutlich lesbar auf die Garantiekarte zu schreiben, damit das Gerät so schnell wie möglich nach Beendigung der notwendigen Reparatur/Einstellung an Sie zurückgesandt werden kann. [. . . ] Los gastos del seguro, manejo y transporte hasta nuestro servicio serán a cargo de la persona demandante de servicio. Para reparación enviar a: 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn. : CAT EYE Customer Service Section #169-6070 Wheel Magnet Aimant pour roue Radmagnet Wielmagneet Magnete ruota Iman de la rueda #166-5150 Lithium Battery (CR2032) Pile au lithium (CR2032) Lithium-Batterie (CR2032) Lithium Batterij (CR2032) Batteria al Litio (CR2032) Bateria de Litio (CR2032) E INSTRUCTION MANUAL A. Main Display(Speed) Wheel Circumference Mark Mode Symbol Mode Button Wheel Sensor Pulse Symbol Speed Scale Symbol Auto Mode Symbol H. Magnet Bracket Rubber Pad (1mm, 2mm) magnet TEST Mount the main unit on the bracket. If current speed doesn't appear on the main display, press either left or right button to release the unit from the power saving mode. Then spin the front wheel to make sure the wheel sensor pulse symbol flickers. If it does not flicker, adjust the position of sensor until it flickers normally. The mounting is completed and the cyclocomputer is operational. OPERATION FEATURES Two buttons are provided on the top of the main unit and two on the bottom. These buttons are used as follows: spoke Fig. 17 COIN ·Mode Button (top left button) Fig. 1 sensor zone about 5mm magnet THE CORDLESS SYSTEM The sensor picks up wheel revolution signal and transmits the signal to the receiver in the main unit. The approximate service hour of batteries is as follows: The main unit (receiver): --- Approx. 2 years (average 1 hour's use per day) The sensor (transmitter): ------- Total distance of approx. Set to a desired wheel circumference in the same manner as the first circumference setting and press SET button to complete the setting. sensor 0. 00 to 999. 99 miles 0. 01mile The trip distance from start to current point is displayed. With Reset operation, it returns to zero. A T A A A T Elapsed Time 0:00'00" to 9:59'59" ±0. 003% Elapsed time is measured from start to current point, in units of hours, minutes and seconds. A Average Speed 0. 0 to 65. 9 miles/hr ±0. 3mile/h The average speed from start to current point is displayed within 27 hours 46 minutes 39 seconds (99, 999 seconds) or 999. 99 miles (km). M Maximum Speed 0. 0 (3. 0) to 65. 9 miles/hr ±0. 3mile/h With Reset operation, it returns to zero and counting begins anew. Clock Time 0:00´ to 23:59´ ±0. 003% The current time is displayed by a 24-hour clock. M magnet Fig. 11 4. Selecting one of the two Wheel Circumference (Fig. 7) Set the Auto Mode to ON. (Refer to the explanation of Auto Mode function. ) While keeping the right button pressed , press the SET button. The first wheel circumference measurement will be displayed for a few seconds, then the second setting will appear. A sensor band B sensor rubber pad sensor band A Fig. 12 sensor band B sensor rubber pad POWER SAVING FUNCTION A 5. How to reset the Wheel Circumference Select the (O) mode and stop the measurement. Press SET button and the already set wheel circumference will blink on the sub-display. Refer to '3. Setting the wheel circumference' to complete the setting. Setting the 24-hour Clock (Fig. 8) When the main unit is left without receiving any signal for one hour, the power will be turned off automatically. [. . . ] Meanwhile, the sensor shall aim at the main unit indicated by the triangle marked on the sensor. Cut the excess sensor zone Fig. 16 sensor band B with scissors or the like. SENSOR with TRANSMITTER TROUBLE SHOOTING No display. ------------------------------------------------------ Replace the main unit battery with new one. -------------------------------------- Execute "All Clear" operation. [. . . ]