User manual DEWALT D27300T

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DEWALT D27300T. We hope that this DEWALT D27300T user guide will be useful to you.


DEWALT D27300T : Download the complete user guide (8343 Ko)

Manual abstract: user guide DEWALT D27300T

Detailed instructions for use are in the User's Guide.

[. . . ] Use a face or dust mask whenever the operations may produce dust or flying particles. If these particles might be considerably hot, also wear a heat-resistant apron. 6 Guard against electric shock Prevent body contact with earthed or surfaces (e. ) , electric safety can be improved by inserting an isolating transformer or a (FI) earth-leakage circuit-breaker. [. . . ] In the planing mode, make sure the upper blade guard is adjusted to provide optimum screening. When working long pieces, use a suitable roller table on both sides of the machine adjusted to the height of the tables. Residual risks The following risks are inherent to the use of planers: In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are: - Risk of accidents caused by the uncovered parts of the rotating blade. - Health hazards caused by breathing dust developed when planing wood, especially oak, beech and MDF. Labels on tool The following pictograms are shown on the tool: A1 1 On/off switch 2 Elevating handle 3 Lower table 4 Shavings collector 5 Scale lower table 6 Push stick 7 Fence clamp handle 8 Fence Fig. Read the instruction manual before use When using the machine in the thicknessing mode, be aware of the direction of feed. When using the machine in the planing mode, be aware of the direction of feed. Do not allow the blades to protrude from the cutterhead by more than 1. Always check that the power supply corresponds to the voltage on the rating plate. The package contains: 1 Partly assembled thickness planer 1 Guard 1 Shavings collector 1 Box containing: 1 Fence 1 Push stick 1 Bag containing: 1 Allen key 2. 5 mm 1 Allen key 4 mm 1 Allen key 5 mm 1 Allen key 6 mm 1 Spanner 13/10 mm 1 Adjustment gauge 1 Elevating handle 2 Clamp handles 4 Rubber feet 1 M8 coach bolt 4 M8 nuts 4 D8 toothed washers 1 D8 flat washer 1 Box containing: 4 Legs 2 Wheels 2 Wheel brackets 1 Bag containing: 2 Wheel axles 4 M8 coach bolts 2 M8 hex head bolts 4 M8 nuts 4 Wing nuts 4 D8 flat washers 6 D8 Belleville washers 1 Instruction manual 1 Exploded drawing · Check for damage to the tool, parts or accessories which may have occurred during transport. Take the time to thoroughly read and understand this manual prior to operation. If an extension cable is required, use an approved extension cable suitable for the power input of this machine (see technical data). Three-phase machines should be wired directly into the mains by a suitably qualified electrician. Under unfavourable power supply conditions, other equipment may be affected. 14 Wheel bracket 15 Wheel axle 16 M8 coach bolt 17 M8 hex head bolt 18 M8 nut 19 Wing nut 20 D8 toothed washer 21 D8 flat washer 22 D8 flat washer 23 D8 Belleville washer Mounting the feet (fig. c1 & C2) With the feet mounted , the machine is suitable for placement on a workbench. To ensure a safe operation, the machine has to be fixed to the workbench. Turn the machine on its side with the thicknessing outfeed frame (24) resting on the floor (fig. Insert a foot (25) into each of the outer notches (26) located in the bottom of the machine housing. Turn the machine on its side with the thicknessing outfeed frame (24) resting on the floor (fig. [. . . ] - extra safety: the hinged safety enclosure plate (51) can be locked by passing a padlock through the hasp (52). The plate also serves as an , , easy to locate" emergency stop button as pressure on the front of the plate will depress the stop button. Snipe Snipe is a depression made when the ends of the workpiece contact the cutters. Turn each adjusting screw (65) in or out as necessary until the blade tip coincides with the gauge. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DEWALT D27300T




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DEWALT D27300T will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.