User manual DEWALT DC728KA

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DEWALT DC728KA. We hope that this DEWALT DC728KA user guide will be useful to you.


DEWALT DC728KA : Download the complete user guide (780 Ko)

Manual abstract: user guide DEWALT DC728KA

Detailed instructions for use are in the User's Guide.

[. . . ] 3 Personal safety a Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. [. . . ] 6 Service a Have your power tool serviced by a qualified repair person using only identical replacement parts. Do not store or carry the battery pack without the battery cap placed over the contacts. In case of eye contact, rinse abundantly with clean water for at least 10 minutes. Labels on charger and battery pack In addition to the pictographs used in this manual, the labels on the charger and the battery pack show the following pictographs: Check for damage to the tool, parts or accessories which may have occurred during transport. Take the time to thoroughly read and understand this manual prior to operation. 1 Variable speed switch 2 Forward/reverse slider 3 Two gear selector 4 Mode selector/torque adjustment collar 5 Collar settings 6 Keyless chuck 7 Bit holder 8 Grip 9 Battery pack Charger Your DE9107 charger accepts DEWALT NiCd battery packs ranging from 7. Your DE9116 charger accepts DEWALT NiCd and NiMH battery packs ranging from 7. 9 Battery pack 10 Release buttons 11 Charger 12 Charging indicator (red) Auto-spindle lock The auto-spindle lock is engaged when the transmission is stationary. The chuck sleeve can easily be turned with one hand while the other supports the unit. Do not probe with conductive objects Read instruction manual before use Use only with DEWALT battery packs, others may burst, causing personal injury and damage Do not expose to water Have defective cords replaced immediately Discard the battery pack with due care for the environment Do not incinerate the battery pack Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains. Always switch off the tool before inserting or removing the battery pack. To charge the battery pack (9), insert it into the charger (11) as shown and plug in the charger. Be sure that the battery pack is fully seated in the charger, but do not force it. The battery pack is now fully charged and the charger automatically switches to equalisation mode. The battery pack can be removed at any time or left in the connected charger indefinitely. If the new pack also refuses to charge, have your charger tested by an authorised DEWALT repair agent. When plugged into power sources such as generators or sources that convert DC to AC, the red charging indicator may blink twice, switch off and repeat. Do not charge the battery pack at ambient temperatures < 4 °C or > 40 °C. To remove the battery pack, press the two release buttons (10) simultaneously and pull the pack out of the grip (8). Without the protective cap in place, loose metal objects could short circuit the contacts, causing a fire hazard and damaging the battery pack. Should your mains plug need replacing and you are competent to do this, proceed as instructed below. [. . . ] 1 low speed/high torque (drilling large holes, driving screws) 2 high speed/low torque (drilling smaller holes) For speed rates, refer to the technical data. The pressure exerted on the variable speed switch determines the tool speed. To lock the tool in the off position, move the forward/reverse slider (2) to the central position. The drill is equipped with a brake to stop the tool as soon as the variable speed switch is fully released. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DEWALT DC728KA




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DEWALT DC728KA will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.