User manual DOMETIC PENGUIN AC INSTALLATION

[. . . ] 620515, 620525, 620526, 630515 & 630516 Installation Instructions RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE: Model Number Serial Number Date Purchased MODEL 620515, 620525, 620526 Roof-Top Air Conditioner 630515, 630516 Roof Top Heat Pump used with one of following: 3105007 Return Air Cover 3105935 Quick Cool Return Air Cover 3308120 Genesis Air Filtration System and 3109228. 001 (White) Comfort Control CenterTM 3109228. 019 (Black) Comfort Control CenterTM THIS UNIT IS DESIGNED FOR OEM INSTALLATION ALL INITIAL INSTALLATIONS MUST BE APPROVED BY THE SALES DEPT. USA SERVICE OFFICE Dometic Corporation 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic Corporation 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 For Service Center Assistance Call: 800-544-4881 C US This manual must be read and understood before installation, adjustment, service, or maintenance is performed. Modification of this product can be extremely hazardous and could result in personal injury or property damage. Lire et comprendre ce manuel avant de procéder à l'installation, à des réglages, de l'entretien ou des réparations. L'installation de cet appareil doit être effectuée par un réparateur qualifié. Toute modification de cet appareil peut être extrêmement dangereuse et entraîner des blessures ou dommages matériels. INSTALLATION INSTRUCTIONS REVISION: Form No. [. . . ] To prevent back injury, use a mechanical hoist to place Air Conditioner on roof. 1. Place the air conditioner on the roof. Important: RJ-11-6C4P connectors must be installed as shown in FIG. This may be accomplished by inserting a small screwdriver under the tab on the bottom edge of the front cover and gently prying. Insert the control cable through the hole in the base plate and mount the plate to the wall with two (2) screws provided. Install the control cable RJ-11-6C4P connector into the back of the Comfort Control CenterTM and snap onto the base plate. This may damage the roof gasket attached to the bottom and may create a leaky installation. FIG. 11 FRONT DE MO N FA UP WN DO NE ZO F OF ON TEM P Insert Screwdriver under Tab 3. Lift and place the unit over the prepared opening using the gasket on the unit as a guide. This box contains mounting hardware for the air conditioner and will be used inside the RV. Minor adjustments can be done from the inside of the RV if required. 9 620515, 620525, 620526, 630515 & 630516 Installation Instructions G. Installing The Air Conditioner Installing Unit with 3105007 or 3105935 Return Air Kit. Hold the ceiling template up to the 14-1/4" x 14-1/4" (±1/8") opening. Start each mounting bolt through the ceiling template and up into the unit base pan by hand. Evenly tighten mounting bolts to compress gasket to 1/2" this will be a torque of 40 - 50 inch pounds. Check gasket alignment of the air conditioner over the roof opening and adjust if necessary. 13 Center Unit From Below Screws Tighten to compress gasket to 1/2" Finger Tight CAUTION Roof Gasket b. Remove return air cover and ceiling template from the 3105007 or 3105935 carton. Locate the four (8" x 1/4- 20) unit mounting bolts, junction box cover and Romex connector in the 3107180 bolt kit. Pull down the unit's electrical cord and fasten the junction box with screws to the framing in the front of the 14-1/4" x 14-1/4" (±1/8") opening. 14 DC Power Furnace Unit CCC Connectors Gasket If bolts are left loose there may not be adequate roof seal or if over tightened, damage may occur to the air conditioner base or ceiling template. Measure the ceiling to roof thickness: · If distance is 2. 0" - 3-3/4", remove perforated tab from divider plate. Remove the backing paper from double sided tape located on ceiling template. [. . . ] Placing the switch in the "ON" position selects that option. 26C DO NOT USE BALL POINT PEN To Move Dip Switch Use Flat Blade Screwdriver Wider Than Dip Switch Slot To Move Dip Switch 1 1 2 3 4 5 6 7 ON ON 2 3 4 5 6 7 8 Not Correct FIG. 26B HEAT STRIP ZONE 2 ZONE 3 ZONE 4 FURNACE DIFFERENTIAL STAGE GEN START HEAT STRIP ZONE 2 ZONE 3 ZONE 4 FURNACE DIFFERENTIAL STAGE GEN START SLIDE SWITCH ROCKER SWITCH All Switches "OFF" All Switches "OFF" Note: Dip switches are in the "OFF" position when shipped from the factory. The dip switches are visible through the opening in the ceiling template into the control box. Dip switches can be either a rocker or sliding style of a switch. [. . . ]