User manual DOMETIC RM2354 INSTALLATION

[. . . ] Be aware of possible safety hazards when seeing alert symbols on the refrigerator as well as in this manual. For information about maintenance and operating instructions, refer to the UseR MaNUal. contents ceRtification anD coDe RequiRements ______ 4 ventilation RequiRements __________________ 4 general information . 6 mounting instRuctions ___________________ 11 Reversing the door swing . 11 RefRigeRatoR Removal ____________________ 12 appenDix a - ReaRview equipment __________ 13 appenDix B - wiRing DiagRams ______________ 16 installation instRuctions __________________ 7 installing the refrigerator . [. . . ] For a proper installation, follow these instructions: · Make sure the floor is solid and level. · The refrigerator must be level and installed in a substantial enclosure. Carpeting must be removed or protected by a metal or wood panel beneath the appliance, which extends at least full width and depth of the appliance. · RM2451, RM2454, RM2551, RM2554, DM2652, DM2662, DM2663, DM2852, DM2862, DM3862, NDM1062 & NDR1292 a wood strip must be in place across the upper opening of the enclosure. The top frame of the refrigerator will be anchored to the wood strip with screws. · When installing the refrigerator in the enclosure, all areas within the recess have to be sealed. Verify that there is a complete seal between the front frame of the refrigerator and the top, sides and bottom of the enclosure. a length of sealing strip is applied to the rear surface of the front frame for this purpose. The sealing strip should provide a complete isolation of the appliance's combustion system from the vehicle interior. RM2351 and RM2354: apply a sealing strip to the foremost floor of the enclosure. Be careful not to damage the sealing strip when the refrigerator is put in place! secuRing the RefRigeRatoR It is important to follow the sequence in securing refrigerator in enclosure since failure in doing so can cause leakage between the frame and cabinet. any space between the counter, storage area or ceiling and top of the refrigerator greater than 1 1/2 inches should be blocked. The heat produced at the rear of the refrigerator will become trapped in this space, making the top of the refrigerator hot and reduce the efficiency of the refrigerator. after the refrigerator is put in place (ensuring a combustion seal at the front frame), the refrigerator is to be secured in the enclosure with screws (not included). Rm2351 & Rm2354 Install the five screws in the following order: 1. One screw installed in the rear base. 2 1 RM2451, RM2454, RM2551, RM2554, DM2652, DM2662, DM2663, DM2852, DM2862, DM3862, NDM1062 & NDR1292 RM2351& RM2354 General view. Two screws installed in the rear base. -8- installation instRuctions DRain wateR hose Drill a hole through flooring. Seal around the hose that goes through the drilled hole and ensure that it does not kink when run through the floor. Check to make sure that the supplied hose is long enough in order for the water to drain outside of the vehicle. If not, the installer will have to supply the extra length of hose. RM2351 & RM2354 The gas supply system must incorporate a pressure regulator to maintain a supply pressure of not more than 11 inches water column. When testing the gas supply system at test pressures: · > 1/2 psi - the refrigerator and its individual shutoff valve must be disconnected from the gas supply piping system. · 1/2 psi - the appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve. If detailed instructions on the installation and connection to the gas supply are required, please contact your dealer or distributor. Testing LP gas safety shut off The gas safety shut off must be tested after the refrigerator is connected to LP gas supply. Hole for drain water hose Rm2354, Rm2454, Rm2554, Dm2662, Dm2663, Dm2862, Dm3862, nDm1062 & nDR1292 To test the gas safety shut off, follow these steps: 1. [. . . ] Before starting the mounting work, read this instruction thoroughly and check that the panel dimensions are in compliance with those given in the following table: max. thickness 5/32" (4 mm) max panel Dimensions Height min max Width min UPPER mm inch 40 401 527 524 20-5/8 1 2 15-27/32 15-25/2 20-/4 1 1 LOWER /SINGLE DOOR RM251 RM254 mm 667 665 498 496 19-17/32 524 20-5/8 524 4 inch 26-17/64 26-/16 19-5/8 827 825 527 20-/4 527 20-/4 1 1 1 3 3 RM2451 RM2454 DM2652 DM2662 DM266 RM2551 RM2554 DM2852 DM2862 NDM1062 FROZEN FOOD COMPARTMENT NDR1292 mm inch 2-9/16 2-1/2 98 981 mm inch 8-11/16 8-5/8 20-5/8 5 mm inch 1402 1400 288 265 55-/16 55-1/8 10-9/16 10-7/16 FRESH FOOD COMPARTMENT NDR1292 mm inch 1402 1400 40 427 55-/16 55-1/8 16-15/16 16-1/16 - 11 - mounting instRuctions Snap in To mount the panel, follow these steps: 1. On new refrigerators, the decoration strip are taped inside the door; if installed on the door, remove the door decoration strip (2) by gently pushing the four tabs away with a flat blade screwdriver (1). Push the panel downwards so that the lower horizontal edge of the panel (4) is fitted into the bottom grove (5). [. . . ]