User manual DURKOPP M-TYPE 867

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DURKOPP M-TYPE 867. We hope that this DURKOPP M-TYPE 867 user guide will be useful to you.


DURKOPP M-TYPE 867 : Download the complete user guide (1681 Ko)

You may also download the following manuals related to this product:

   DURKOPP M-TYPE 867 (1696 ko)
   DURKOPP M-TYPE 867 (1694 ko)

Manual abstract: user guide DURKOPP M-TYPE 867

Detailed instructions for use are in the User's Guide.

[. . . ] 867 Spezialnähmaschine Betriebsanleitung Instruction manual Instructions d'emploi D GB F Postfach 17 03 51, D-33703 Bielefeld · Potsdamer Straße 190, D-33719 Bielefeld Telefon +49 (0) 521 / 9 25-00 · Telefax +49 (0) 521 / 9 25 24 35 · www. duerkopp-adler. com Ausgabe / Edition: 04/2010 Änderungsindex Rev. index: 05. 0 Printed in Federal Republic of Germany Teile-Nr. /Part. -No. : 0791 867740 Alle Rechte vorbehalten. Eigentum der Dürkopp Adler AG und urheberrechtlich geschützt. Jede, auch auszugsweise Wiederverwendung dieser Inhalte ist ohne vorheriges schriftliches Einverständnis der Dürkopp Adler AG verboten. [. . . ] ­ Fasten the lever 4 of the knee lever with the screw 7 and washer 8. ­ Adjust the knee lever so that it can be conveniently operated with the right knee. ­ Tighten screw 3 again. 4 6 8 7 18 5. 5 Fitting the operating panel 4 3 ­ ­ ­ ­ 1 6 5 ­ ­ ­ Unscrew the thread guide 2 from off the sewing machine head. Fix the control panel fixing angle 1 together with the thread guide 2. Lay the power supply cable 5 of the operating panel: along the arm and down through the opening in the table plate 6 or down through the arm and the base plate - and secure it. Replace the valve cap 4. GB 5. 6 Fitting the sewing lamp (optional equipment) Caution !Turning off the main switch does not turn off the current to the sewing lamp. Remove the mains plug before connecting. 19 4 3 1 6 5 7 8 The sewing lamp can be mounted on the operating-panel bracket if present. ­ Stick the safety warning label on the front of the main switch 7. ­ Pass the power supply cable down through the hole in the table plate or the arm and the base plate. ­ Attach the transformer 8 under the table plate with chipboard screws. ­ Attach the power supply cable under the table plate with cable ties. All work on the electrical equipment of this special sewing machine may only be carried out by qualified electricians or other appropriately trained persons. The mains plug must be removed. 6. 2 Checking the mains voltage Caution !The mains voltage must agree with the rated voltage specified on the model-identification plate. 6. 3 6. 3. 1 Connecting the sewing drive Connecting the clutch motor ­ Lay the connection cable from the main switch through the cable conduit to the sewing drive and connect it to the sewing drive. See connection diagram 9800 169002 B (in the connection pack) or the circuit diagram on the clutch motor. Lay the mains cable from the main switch back through the cable conduit and attach to the mains-lead cleat. GB ­ 6. 3. 2 Connecting the coupling-positioning actuator ­ Lay the connection cable from the motor-protection switch through the cable conduit to the sewing drive and connect it to the sewing drive. See connection diagram 9800 129002 B (in the connection pack) or the circuit diagram on the coupling-positioning actuator. Lay the mains cable from the main switch back through the cable conduit and attach to the mains-lead cleat. Plug the cable from the set-point generator into socket b80 of the drive control. See figure page 20. ­ ­ 6. 3. 3 Connecting the direct-current positioning actuator ­ ­ ­ Lay the connection cable from the main switch through the cable conduit to the sewing drive and connect it to the sewing drive. Lay the mains cable from the main switch back through the cable conduit and attach to the mains-lead cleat. [. . . ] Machines equipped with binding device Mount the M-Control PCB 1 between the stand 4 and the cable duct 3. 4 6 8 2 10 5 10 9 8 7 ­ ­ ­ 6 Connect the compressed air hose 7 to the compressed-air maintenance unit 5. Connect both compressed air hose 10 from the machine head to the solenoid valves 8 and 9. Plug the electric cables into the corresponding sockets. Note ­ If the function of the keys "L" and "R" are permuted, swap the compressed air hoses 10 at the solenoid valves. 32 6. 14 Setting the switches on the M-Control PCB 1 Machines equipped with binding device The switch 3 on the M-Control PCB must be set to "1" on machines equipped with the moving binding device. Machines with disconnectable needle bars The switch 3 on the M-Control PCB must be set to "2" on machines with disconnectable needle bars. GB 33 Notes: 34 6. 15 Setting machine-specific parameters 6. 15. 1 General The functions of the sewing-drive control are determined by the program and the parameter settings. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE DURKOPP M-TYPE 867




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DURKOPP M-TYPE 867 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.