User manual EPSON DLQ-2000 ESCP MANUAL

[. . . ] Only the right one is on when envelope is selected as the paper type. Only the left one is on when card is selected as the paper type. 2 Reset When you press both the Font and Pitch buttons simultaneously, the printer clears buffer and returns to its default settings. 3 Pitch button Selects one of the pitch settings. Pitch lights Indicate which pitch is selected. Buttons and Lights (1/2) EPSON DLQ-2000 Quick Guide 5 Paper Source button Selects a paper source. Ejects a single sheet or advances continuous paper to the next top-of-form position when held down for a few seconds. [. . . ] While aligning the left side of a sheet of paper with the edge guide, insert it into the printer until it meets resistance. Be sure to load paper printable side up. After a few seconds, the printer automatically advances the paper to the loading position. The printer is ready to start printing. Off al Paper ff pe Paper Source Tractor Manual/CSF Pau 3s LF/F c Caution: Use the knob on the right side of the printer only to clear paper jams when the printer is off. Otherwise, you may damage the printer or cause it to lose the top-of-form position. Do not open the printer cover while paper is being fed; otherwise the printer cannot load the paper correctly. 4. Slide the edge guide until it rests against the guide mark. Note: If the platen rotates but the printer does not load the paper, completely remove the paper and then insert it all the way into the printer again. If the paper feeds before you can adjust its position properly, increase the Manual feed wait time in the default-setting mode. See "Changing default settings" for more information. * guide mark Single Sheets with the Paper Guide (1/2) EPSON DLQ-2000 Quick Guide If you need to adjust the position of the paper after it is loaded, see "Adjusting the top-of-form position" and follow the instructions. After printing a sheet, the printer ejects it onto the paper guide and the Paper Out and Pause lights come on. If you are printing a multiple-page document, remove the printed sheet and insert a new sheet into the paper guide. Note: If the printer does not eject the printed sheet, press the Load/Eject button. Single Sheets with the Paper Guide (2/2) EPSON DLQ-2000 Quick Guide Single Sheets with the Cut-Sheet Feeder Loading paper to the cut-sheet feeder For single-sheet multipart forms, use only the type of forms that are glued at the top. Note: Make sure to insert paper between the two arrow marks on the unit. c Caution: Use the knob on the right side of the printer only to clear paper jams when the printer is off. AUTO 9 8 7 6 5 4 3 2 1 0 -1 4. The printing position (the position of the first letter of the first line) is set to 3 mm (0. 12 inch) from the left edge of the paper by default. See "Adjusting the printing position" in the Reference Guide for more information on the printing position. A * paper-thickness lever 3. Insert paper into the automatic sheet alignment unit so that the tip of the paper goes behind the rollers of the unit. The printer automatically aligns the paper, recognizes the right and left edges (the width) of the paper and starts feeding. A. If the printed sheet remains in the printer, press the Load/Eject button to eject it. 1. arrow marks Single Sheets with the Automatic Sheet Alignment Unit (1/1) EPSON DLQ-2000 Quick Guide Special Papers Multipart forms Your printer can print on both single-sheet and continuous multipart forms. It can use multipart forms with up to eight parts including the original. Overlapping multipart forms Overlapping multipart forms are a type of continuous paper with multipart forms. The page length of the multipart forms is longer than that of the backing continuous paper. So when extended, one page's multipart forms overlap the next page's multipart forms as shown below. This overlapping area is thicker than the printable area. c Caution: Use only carbonless multipart forms. Before printing, set the paper-thickness lever to the appropriate position for your multipart forms referring to the table in "Paper-Thickness Settings. " You can load single-sheet multipart forms from the paper guide, or with the optional cut-sheet feeder or optional automatic sheet alignment unit. [. . . ] Tear off the printed pages. Note: Your tear-off position setting remains in effect until you change it, even if you turn off the printer. Make sure the Tear Off/Special Paper lights are flashing (the paper is at the current tear-off position). You may need to press the Tear Off/Special Paper button to advance the paper to the tear-off position. The Pause light begins flashing and the printer enters the Micro Adjust mode. 6. [. . . ]