User manual EPSON EMP-X3

[. . . ] The output destination can normally be changed by holding down the computer's key and pressing one of the Function keys. Once the source has been changed, after a short wait the projector will start projecting. For details, refer to the documentation provided with your computer. If images do not appear . . . Change the input signal. Each time is pressed, the image source cycles between Computer/Component Video, S-Video, and Video. Projector Remote Control If you have other problems . . . Refer to the online Help information. Examples of changing output NEC Panasonic TOSHIBA IBM SONY FUJITSU Macintosh After startup, change the Control Panel adjustments so that Mirroring is active Press on the projector's control panel and follow the prompts which appear in order to solve the problem. Projector * Refer to "Troubleshooting". Projecting Adjustment "Adjusting the Screen Image" in User's Guide Adjusting the projection angle Use the foot adjust buttons to adjust the projection angle of the projector. [. . . ] While pressing the foot adjust buttons, lift up the front of the projector. When the projector is tilted, it will cause keystone distortion to appear in the image, but this distortion can be corrected using the automatic keystone correction function as long as the vertical angle of tilt is within a range of approximately 15°. If you would like to make further minor adjustments to the effects of automatic keystone correction, use panel. on the projector's control Tip If the front adjustable feet have been extended, they can be retracted again by pressing and holding the foot adjust buttons on both sides of the projector and gently pushing down the front of the projector. If the images become uneven in appearance after keystone correction is carried out, decrease the "Sharpness" menu setting. Adjusting the image size and focus Focus adjustment Image size adjustment Turn to "W" to enlarge Turn to "T" to reduce "Manually Correcting Keystone Distortion" in User's Guide To make further adjustments after automatic keystone correction To make further adjustments after automatic keystone correction has been carried out, press on the projector's control panel. Tip If "Auto Keystone" in the "Setting" menu is set to "OFF" (the default setting for this item is "ON"), automatic keystone adjustment is not carried out. Press on the projector's control panel to adjust the keystone at this time. When the top is too wide When the bottom is too wide Adjustment / Turning Off the Projector Adjustment "Using the Configuration Menu Functions" in User's Guide Other adjustments Press the on the remote control to display the configuration menu on the screen. You can then adjust the individual brightness, contrast and sharpness settings. Press control. on the remote The configuration menu appears. Tip Press menu level. to return to the previous Use and to select the menu item to be set, and then press . The selected sub-menu then appears. Remote control Main menu Sub-menu (Video) Use and to select an item, and then use and to adjust the setting or select "ON" or "OFF". To close the menu, press . Turning Off the Projector "Turning Off the Projector" in User's Guide Turn off the power for the equipment connected to the projector. Then select the type of screen to be displayed when projection is being stopped. The following choices are available. The default setting is the black screen. Use the menus to set your own user's logo if desired. Solid black Solid blue User's logo Functions for Enhancing Projection Troubleshooting "Using the Help" in User's Guide Viewing the online help This projector is provided with an online help function which can be used when you have a problem using the projector. Press on the projector's control panel. Or press on the remote control. The help contents will then be displayed. To clear the help display, press on the projector's control panel. "When Having Some Trouble" in User's Guide Checking the indicators You can check the status of the projector using the indicators on the projector's control panel. Refer to the table below for details on checking and remedying the cause of problems. Warning indicator Power indicator (Warning) indicator Status : lit : flashing Problem and remedy High temperature inside projector (overheating) The lamp will turn off automatically and projection will stop. After 5 minutes have elapsed, unplug the power cable and then plug it back in again. Then press on the projector's control panel or on the remote control to turn the power back on Lamp problem Remove the lamp and check if it is broken. If the lamp is broken replace by a new lamp, or contact your local dealer for further advise. [. . . ] Then press on the projector's control panel or on the remote control to turn the power back on Lamp problem Remove the lamp and check if it is broken. If the lamp is broken replace by a new lamp, or contact your local dealer for further advise. *1 Red indicator Status : lit : flashing Problem and remedy Standby condition The power cable should only be disconnected when the projector is in this condition. [. . . ]