User manual EPSON STYLUS DX3800

[. . . ] Lift the printer cover. 4 Unwrap the ink cartridges. Don't touch the green circuit board or remove any labels. 5 Open the cartridge cover and remove the paper insert. 6 Lower each cartridge into its holder with the green circuit board facing the front. The color of the cartridge label should match the marker on the holder. Then gently push each ink cartridge down until it is firmly seated. 7 Close the cartridge cover. 8 Press forward on the front left corner of the cartridge cover to lock it in place. 9 Press the Maintenance button and close the printer cover. CAUTION: Don't turn off the printer or interrupt charging while the light is flashing or you'll waste ink. [. . . ] CAUTION: Don't turn off the printer or interrupt charging while the light is flashing or you'll waste ink. A progress bar is displayed on the LCD panel during ink charging. 10 After ink charging is finished, press OK. 4 Load Paper 1 2 Fan a few sheets of paper and load them against the right side of the sheet feeder. NOTE: For instructions on loading and printing on CDs or DVDs, see your User's Guide. 5 Install Software Windows ® Make sure your printer is NOT connected to your computer, then follow the steps below. 1 Turn on your computer. Wait for the system to start up, then insert the EPSON® CD-ROM in your drive. NOTE: If you see a screen like this, click Cancel and disconnect the printer from your computer. 2 3 Read the license agreement that appears and click Agree. You see a message like this: Click OK to begin installing your printer driver. 4 When you see this screen, connect the square end of your USB cable to the back of the printer and the flat end of the USB cable to your computer. (You can connect to any open port. ) NOTE: For Windows XP, if you don't have USB 2. 0, you see a message. Click the Close button to close the message. Square end Flat end Wait while Windows detects your hardware. 5 6 When you see this screen, click Continue. Follow the on-screen instructions to install your software. continue 7 When installation is complete, you see this screen: To install EPSON SoftwareTM Film Factory, TM click EPSON Software Film Factory, then click Install. Click Back, then click Back again. 7 8 9 10 11 12 13 14 From the Install Menu, click Install Printer Manual to install your on-screen Reference Guide. Follow the on-screen instructions to register your printer. Go to the section for your operating system to finish setting up your printer. continue Mac OS X 10. x 1 Open the Applications folder, then open the Utilities folder and select Print Center. If you don't see it, make sure your printer is turned on and connected. Then click Add or Add Printer, and select EPSON USB at the top of the screen and Stylus Photo R300 below. Then go to step 3. 2 Click the Stylus Photo R300 printer name and then click the Add or Add Printer button. If it isn't already selected, choose EPSON USB. 3 Click the printer name, then open the Page Setup menu at the bottom of the screen and select All. 4 5 Click the Add button. See section 6, "Print. " NOTE: To print from Macintosh Classic applications in OS X, restart your Macintosh in OS 9 and follow the "Install Software" steps again. Macintosh OS 8. 6 to 9. x Open the Chooser from the Apple® menu, then select these options: · SP R300 Series · Your USB port · Background printing (on or off) Close the Chooser. See section 6, "Print. " 6 Print Now you're ready to print. [. . . ] If it isn't already selected, choose EPSON USB. 3 Click the printer name, then open the Page Setup menu at the bottom of the screen and select All. 4 5 Click the Add button. See section 6, "Print. " NOTE: To print from Macintosh Classic applications in OS X, restart your Macintosh in OS 9 and follow the "Install Software" steps again. Macintosh OS 8. 6 to 9. x Open the Chooser from the Apple® menu, then select these options: · SP R300 Series · Your USB port · Background printing (on or off) Close the Chooser. See section 6, "Print. " 6 Print Now you're ready to print. [. . . ]