User manual EWT CS3 COMFORT

[. . . ] WARNINGS AND GUIDELINES CONCERNING SAFETY • This appliance complies with current safety regulations for electrical appliances. Please read these instructions for use fully and carefully before operating the appliance. You should keep the instructions for use, the guarantee coupon and proof of purchase as well as the packaging as far as this is possible. € This appliance has been designed exclusively for personal use and for its intended purpose. [. . . ] Pay special attention to the following “special safety instructions”. Special safety instructions: Do not vacuum hot ashes or pointed or sharp-edged objects. Do not use the appliance without a dust bag (except when vacuuming liquids). When using the appliance, make sure that the brush or nozzle does not vacuum anybody’s hair, clothes or limbs. Keep the vacuum cleaner away from sources of heat such as radiators, stoves, etc. Recommendations with regard to disposal: This appliance has electrical and electronic components and should not be disposed of with domestic waste. 30 SPECIFICATIONS Maximum power Mains voltage Container capacity Pipe system Hosepipe Cable Plug (Prise Confort) Container material Motor type Blow function Hosepipe storage on the head (=Easy-Storage) Cable hook Space for accessories Main floor brush Split mouthpiece Tube Step rubber adaptor (Ø35mm) Dust filters Liquid filter 1500 W 230 V~50Hz 23 L tank Ø35 mm 2, 1 m 5m Yes Stainless-steel E-motor Yes Yes Yes Yes 1 1 3 1 1 dust bag 1 Reusable cloth filter 1 Foam filter 31 LOCATION OF PARTS B A Carefully remove the contents of the box. A B C D E F G H I J K L M N Wet/Dry Vacuum Cleaner Hose Floor Nozzle Extension Wand Crevice Tool Step Rubber Adaptor Foam Sleeve Filter Reusable Cloth Filter Dust Bag 360° Casters Large Notched Wheel Handle 6 Screws (bag) Operator’s Manual 1 1 1 3 1 1 1 1 1 2 2 1 1 1 C D E F G H I J K L M N NOTE: The hose and accessories for this wet and dry vacuum cleaner are 35mm diameter. Then add the 2 notched wheels fixing them with 2 of the screws provided (Fig. Place the handle in the slots located on the vacuum head and secure it with the 2 screws provided (Fig. To vacuum dust, install the reusable cloth filter (or optionally the cartridge filter) and the paper bag (Fig. Adjust the upper part on the container clasps and secure by pressing it down (Fig. Insert the largest end of the hosepipe into the suction port on the front of the container and lock it by gently pushing and turning it (Fig. Select the desired end piece or the extensions and fit them onto the hosepipe (Fig. Plug the power tool into the “Integrated Socket” on the vacuum cleaner. €: Stop Image B: Integrated socket Power tools such as: drills, saws or sanders up to max, 2000W can be plugged directly into the integrated electrical socket (21) on the vacuum cleaner. Connect the hosepipe (Ø35mm) to the dust extraction outlet on the power tool using the adaptor supplied for the tool. (You will find other suitable adaptors in specialist and DIY stores). Plug the power tool into the “Integrated Socket” on the vacuum cleaner. WARNING: Only plug the vacuum cleaner into an earthed socket with a 16 Amp capacity. After a short lapse of time, the vacuum cleaner starts up and vacuums the dust and shavings produced. DELAYED SHUT DOWN After the power tool is switched off, the vacuum cleaner continues to work for a certain time in order to vacuum the dust and shavings remaining in the power tool and the hosepipe. [. . . ] 40 INSTALLING AND CLEANING FOAM SLEEVE FILTER 1 2 3 4 5 Installing Foam Sleeve Filter 1. Carefully slide foam sleeve filter down over the filter cage making sure the whole cage is covered. With the removed power head in the upside down position, carefully remove foam sleeve filter (Fig. Use a mild soap and water solution to wash foam sleeve filter and rinse with clean water (Fig. [. . . ]