User manual FALMEC LUMEN INSTALLATION SHEET

[. . . ] Please become familiar with these recommendations before installing and using your oven. They were written for your safety and the safety of others. Note In the case of a kitchen heated by a device connected to a chimney (a stove, for example) the ?recycling?Suitable ventilation should be provided in the room when the hood is used at the same time as appliances operated by gas or another combustible fuel. -When frying food under the appliance, you must carefully monitor the preparation at all times. -The hood should never be used over a combustible fuel burning stove (wood, coal, etc. ). [. . . ] -This appliance is not intended for use by persons (including children) with impaired physical, sensory or mental capacities, or by inexperienced or untrained persons, unless they have received prior instruction or supervision in its operation by a person responsible for their safety. Children must be supervised to prevent them from playing with the appliance. -When you receive the appliance, unpack it or have it unpacked immediately. Make note of any concerns or reservations on the delivery slip and make sure that you keep a copy of this form. Do not use it for commercial or industrial purposes or for any other purpose than that for which it was designed. -Do not modify or attempt to modify any of the characteristics of this appliance. -Always unplug the hood before cleaning it or performing other maintenance work. -Provide adequate ventilation for the room in the case of simultaneous use of the hood and other appliances powered by an energy source other than electricity. dishes under the hood or operate gas rings under the hood without placing cookware on them (the flames sucked up into the hood can damage the appliance). CARE FOR THE ENVIRONMENT ?This appliance?s packing materials are recyclable. Please recycle the packaging and help protect the environment by placing it in the recycling bins provided by your local council. -Place the carbon filter in the filter cartridge with the 2 metal attachment brackets (see section on changing the carbon filter). -Secure the grid (4) in place with the 2 screws provided. 1 2 1 2 4 3 9 EN 3 / USING YOUR APPLIANCE Eolysis Light Timer Boost Speed 3 Speed 2 On/Off - Speed 1 Tip This Guide to Installation and Use is valid for several models. There may be minor differences between the details and fittings on your appliance and the description provided. 10 3 / USING YOUR APPLIANCE EN CONTROL PANEL DESCRIPTION ?On/Off Pressing the button starts the hood in speed 1 (the button turns the hood off. Cartridge filter saturated The button flashes (1 short flash) for 2 minutes after the hood stops to signal that the cartridge filters must be cleaned (see section ?Cleaning the cartridge filter?). Carbon filter saturated The button flashes (2 short flashes) for 2 minutes after the hood stops to signal that the carbon filters must be cleaned (see section ?Changing the carbon filter?). Change speed Once the hood has started, you can modify the suction speed by pressing speed 2 ( is lit) or for speed 3 ( is lit). for The function allows your hood to remain at maximum speed 4 for 10 minutes, before switching back to speed 2. ?Configure recycling mode (or evacuation mode as an optional extra) A long press (more than 2 sec) on the Evacuation or Recycle mode. and and buttons allows you to select or button button is buttons are lit and the button flashes and the selects recycle mode (the selects evacuation mode (the button flashes and the A short press on confirms the configuration (or automatic set after 10 sec). The hood?s default mode is evacuation. 11 EN 3 / USING YOUR APPLIANCE ? [. . . ] For an hour, the hood alternates button between a 5-minute interval running in speed 1 and a 10-minute pause. . To stop the function, press more. Programming the Eolysis function A long press on the button activates programming. button, indicating the start of The button flashes alternately with the programming. Each short press on the button increases the eolysis time by one hour (from 1 hour to a maximum of 9 hours) and after 9, this display goes back to 1. button (the number of successive flashes is the number of . Programming is confirmed automatically after 25 seconds or by a short press on (The button flashes alternately with the button). Programming is confirmed by pressing the button; press it a second time to cancel. ? [. . . ]