User manual FALMEC ONDA1440

[. . . ] Any modifications that may be required to the electrical system for the installation of the range hood must only be made by qualified electricians. It is dangerous to modify or attempt to modify the characteristics of this system. In the event of malfunctions or if repairs are required to the appliance, do not attempt to solve the problems directly. For all repair and other work on the appliance, contact an authorised service/spare parts centre. [. . . ] For maximum efficiency, the third speed should be used when there are strong odours or a lot of steam, the second speed in normal conditions, and the first speed for keeping the air clean with minimum energy consumption. The range hood should be switched on when starting to cook, and left on until the odours disappear. SPEED - Switch B This is used to start and set the speed of the motor, from 1 to 3, or with continuous speed variator, depending on the version. FIVE BUTTON CONTROL PANEL LIGHT- button Pressed: the light is on Released: the light is off MOTOR button - 1, 2, 3, OFF 1: starts the motor at minimum speed 2: starts the motor at medium speed 3: starts the motor at maximum speed OFF: stops the motor 3. ELECTRONIC CONTROL PANEL Light pushbutton • ON: light on (the pushbutton is lit); • OFF: light off; Pushbutton Press to reduce motor speed Speed 1, 2 and 3 are indicated by the number of LEDs that light up (excluding the light and the timer LEDs). Pushbutton + Press to increase motor speed Speed 1, 2 and 3 are indicated by the number of LEDs that light up (excluding the light and the timer LEDs). The function “desired speed” enables to start the motor at the speed that was selected before the hood was last turned off. WARNING: Install the hood away from sources of electromagnetic waves, as these could affect the correct operation of the electronic system. The maximum operating distance could be less than 5 metres in case of electromagnetic interference by other equipment. 17 – and + pushbutton: increase/decrease speed (to start the motor press either the + or the – pushbutton). Timer and ‘filter clogged’ alarm pushbutton • This function allows the automatic turning off of the hood after running for 15 minutes at the speed previously set (the pushbutton shows a flickering light). € After about 30 hours of running the pushbutton indicates the need for washing the metal filters (the pushbutton shows a solid red light). To disable the alarm press the pushbutton for a few seconds until the red light turns off. Then turn the hood off and on again to check that the alarm has disappeared. METAL FILTERS To remove the metal grease-trapping filter, simply pull the handle A until releasing it from the front guide; then tilt it slightly downwards, and slide it out of the rear guide. CHARCOAL FILTERS To replace the charcoal filters, proceed as follows: remove the metal filters as described above. The two filters located at the ends of the motor can now be easily accessed. In case of hood with the motor box the filter is located on the botton part of the motor box. LIGHT BULB ASSEMBLY AND REPLACEMENT To replace the light bulb: a) Make sure the appliance is disconnected from the mains power supply. C) Replace the light bulb with the same model as the original (max 25 W, see the markings near the light). Light bulbs with different shapes and power ratings from the original may seriously damage the light compartment. SPOTLIGHT To replace the lamp for “Round halogen light”: a) Make sure the appliance is disconnected from the mains power supply. [. . . ] - Tighten the extension cable (H) to the bracket (L) by means of the screws (M) Power the hood in compliance with the regulations in force (section D). Round halogen light Auswechseln der Lampe “Dicroic lamp”: a) Sich vergewissern, dass das Gerät nicht an das Stromnetz angeschlossen ist. 33 C MONTAGE (partie réservée au personnel qualifié pour le montage de la hotte) Distance minimale: distance entre la surface de support des casseroles sur la table de cuisson et la partie la plus basse de la hotte. Quand la hotte est placée au-dessus d’un appareil à gaz, cette distance doit être d’au moins 65 cm (voir figure C1). [. . . ]