User manual FALMEC RUBIK E.ION

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FALMEC RUBIK E.ION. We hope that this FALMEC RUBIK E.ION user guide will be useful to you.


FALMEC RUBIK E.ION : Download the complete user guide (24841 Ko)

Manual abstract: user guide FALMEC RUBIK E.ION

Detailed instructions for use are in the User's Guide.

[. . . ] Before installing the hood, check that the electrical mains power supply corresponds with what is reported on the identification plate located inside the hood. The socket used to connect the installed equipment to the electrical power supply must be within reach: otherwise, install a mains switch to disconnect the hood when required. Any changes to the electrical system must be carried out by a qualified electrician. The maximum length of the flue fastening screws (supplied by the manufacturer) must be 13 mm. [. . . ] POSITIONING The minimum distance between the highest part of the cooking equipment and the lowest part of the hood is indicated in the installation instructions. Generally, when the hood is placed over gas cookers, the distance must be at least 65 cm (25. However, according to an interpretation of standard EN60335-2-31 dated 11-07-2002 of TC61 (sub-clause 7. 11), the minimum distance between the cooker and lower part of the hood can be reduced to the quota reported in the installation instructions. Should the instructions for the gas cooker specify a greater distance, this must be taken into consideration. Do not install the hood outdoors and do not expose it to outdoor environment (rain, wind, etc. Make sure the zeolite-carbon filters are installed in the hood, otherwise, apply them as indicated in the assembly instructions. ASSEMBLY INSTRUCTIONS only intended for personnel qualified The hood can be installed in various configurations. The generic assembly steps apply to all installations; for each case, follow the specific steps provided for the required installation. Switch on the hood at least one minute before starting to cook to direct fumes and vapours towards the suction surface. After cooking, leave the hood operating until complete extraction of all vapours and odours. By means of the Timer function, it is possible to set auto switch-off function which will allow the hood to turn off automatically after 15 minutes of operation. The higher the number of pollutant agents, the darker the yellow colour. (only intended for qualified personnel) Disconnect the equipment from electrical mains power supply before carrying out any operations on the hood. Ensure that the wires inside the hood are not disconnected or cut: in the event of damage, contact your nearest Servicing Department. Connection must be carried out in compliance with the provisions of law in force. Before connecting the hood to the electrical mains power supply, check that: • voltage supply corresponds with what is reported on the data plate located inside the hood; • the electrical system is compliant and can withstand the load (see the technical specifications located inside the hood); • the power supply plug and cable do not come into contact with temperatures exceeding 70 °C; • the power supply system is effectively and properly connected to earth in compliance with regulations in force; • the socket used to connect the hood is within reach. In case of: • devices fitted with cables without a plug: the type of plug to use is a ''standardised'' one. The wires must be connected as follows: yellowgreen for earthing, blue for neutral and brown for the phase. € fixed equipment not provided with a power supply cable and plug, or any other device that ensures disconnection from the electrical mains, with an opening gap of the contacts that enables total disconnection in overvoltage category III conditions. Said disconnection devices must be provided in the mains power supply in compliance with installation regulations. The Manufacturer declines all responsibility for failure to comply with the safety regulations. [. . . ] V1 BORTSKAFFELSE VED ENDT LEVETID Symbolet med den overstregede affaldsspand, der er gengivet på deres apparat, betyder at produktet indgår i kategorien WEEE, dvs, “Waste Electrical and Electronic Equipment" (affald af elektriske og elektroniske produkter) hvorfor det ikke må bortskaffes sammen med dagrenovationen som almindeligt affald, men skal behandles særskilt for at kunne genanvendes, eller undergå særlig behandling for udskillelse af eventuelt skadelige dele/stoffer, der bortskaffes med respekt for miljøet. Korrekt bortskaffelse af dette produkt medvirker til at spare værdifulde resurser og undgå potentielle negative påvirkninger for folkesundheden og omgivelserne, som omvendt kan forårsages af en ukorrekt bortskaffelse af affaldet. kontakt venligst de lokale myndigheder , for at indhente yderligere oplysninger om det nærmeste indsamlingspunkt. Der kan være fastsat bøder for ukorrekt bortskaffelse af denne type affald i den nationale lovgivning. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FALMEC RUBIK E.ION




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FALMEC RUBIK E.ION will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.