Detailed instructions for use are in the User's Guide.
[. . . ] MODELS PL30DD & PL36DD DOWNDRAFT BLOWER SYSTEM
READ AND SAVE THESE INSTRUCTIONS !INTENDED FOR DOMESTIC COOKING ONLY !
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. If you have questions, contact the manufacturer at the address or telephone number in the warranty. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. [. . . ] Bottom flange may have to face inward in tight cabinet installations. ) 2. Secure the downdraft to the countertop as follows: Hold the downdraft against the back of countertop cut-out and tightening the 2 mounting screws (one on each end of unit) on underside of countertop. Tighten screws holding leveling bracket to unit on each side.
INSTALL DUCTWORK
CAUTION - BEFORE CUTTING HOLE IN CABINET FOR DUCTWORK: Check for interference with floor joists, wall studs, electrical wiring or plumbing.
WIRING DIAGRAM
SCREWS
1. Mount the roof or wall cap and work back towards the cabinet, attaching all ductwork, elbows and transitions as previously planned. If necessary, LOOSEN nuts and screws that hold the blower in place, and slide blower left or right to meet ductwork. Note: A 3-1/4" x 10" collar is provided for installers who prefer to rivet the ductwork to the unit. This will allow blower to be removed and replaced easily in service situations without disturbing ductwork.
INSTALL ELECTRICAL WIRING
1. Mount a standard wiring box, with 3-pronged receptacle, inside the cabinet. Run appropriate power cable into cabinet and connect it to receptacle. Plug the downdraft's power cord into the outlet.
BLOWER
COLLAR
3-1/4" X 10" TO 6" RD. Note: Accurate alignment of cooktop and downdraft is necessary to ensure that there is no interference when air vent is raised and lowered. There should be a gap of 1/32"-1/16" between the back of the cooktop and the front of the downdraft cover.
ADJUSTMENT
The downdraft is factory-adjusted for proper operation. However, shipping and handling may affect the position of the activating switch. To adjust position of activating switch:
WARNING: To avoid possible electrical shock, personal injury or death Disconnect electrical power.
1. Lift air vent straight up and cock it slightly so it remains in the UP position.
SWITCH MEMBRANE
SCREWS
SWITCH BRACKET
SWITCH COVER
3. Position switch bracket so that activating switch just comes in contact with underside of switch membrane. Replace switch cover, gently lower air vent into chimney, and plug in power cord. Re-connect electrical power and check operation.
4
USE AND CARE
Always turn the downdraft blower on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clean the air after you turn the cooktop off. 5 PH Trim Cover, Air Box Opening Nut, #10-24 Air Box Cover Gearmotor Bracket Assembly Leg Support Screw, 1/4-20 x 5/16 Washer, 1/4 Screw, #8-32 x 1/2 PH HD MS Screw, #10-24 x 3/8 SH WH LOCK Screw, #10-24 x 3/8 PH FL HD LD Nut, 10-24 HEX KEPS Nut, 1/4-20 WHIZ LOCK U-Bolt, 10-24 Strain Relief Nut, Hex Flange Wire Channel Clamp Wire Tie Capacitor Screw, 1/4-20 x 1. 250 HEX HD #8-18 x . 250 PH TR HD BPT Seal - Foam Blower Assembly, Complete (Includes Key Nos. 2, 9, 20, 21, 22, 28, 31, 32, 49, 58, 64, 65, & 73) Chimney Assembly, Complete (Includes Key Nos. 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 4 19 2 6 2 1 4 1 1 2 5 2 4 1 1 7 3 1 1 1 2 3 1 2 2 1
OPTIONAL TOP COVER KITS
MODEL NO. HT2730B HT2736B HT2730W HT2736W DESCRIPTION 30" Black 36" Black 30" White 36" White
*Standard Hardware - May be purchased locally. [. . . ] Re-connect electrical power and check operation.
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used, and maintained in accordance with the provided instructions.
Exclusions This warranty does not cover the following: 1. Products with original serial numbers that have been removed, altered or cannot be readily determined. Product that has been transferred from its original owner to another party or removed outside the USA or Canada. [. . . ]