User manual FUJIFILM FINEPIX A205S

[. . . ] Getting Ready Using the Camera Advanced Features Settings Software Installation This manual will show you how to use your FUJIFILM DIGITAL CAMERA FinePix A205/A205S/A210 correctly. Please follow the instructions carefully. Viewing Images BL00278-201(1) Warning To prevent fire or shock hazard, do not expose the unit to rain or moisture. EC Declaration of Conformity to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. You are cautioned that any changes or modifications not expressly approved in this manual could void the user's authority to operate the equipment. [. . . ] Sets the volume of the tone emitted when the camera controls are used. Use this option to specify whether the LCD monitor is automatically switched ON or OFF when the Mode switch is set to "q". Specifies whether frame numbers are assigned consecutively from previous numbers or begin again. Use this setting to specify the language used for LCD monitor display. Resets all the camera settings other than the date and time, language and video output settings to the factory default values set at shipment. To reset the settings, press the "MENU/OK" button. Power consumption is kept to a minimum to prevent battery depletion. Select the "ON" setting when you are using alkaline batteries. POWER SAVE FORMAT § BEEP DATE/TIME qLCD ON/OFF OK LOW/HIGH/OFF SET ON/OFF ON ­ LOW ­ ON !G The Power Save setting is disabled during automatic playback, during rechargeable battery discharging and when a USB connection is being used. FRAME NO. ¶ ENGLISH VIDEO SYSTEM DISCHARGE qRESET NTSC/PAL OK ­ ­ h Power saving "ON" 1 If the camera is not used for approximately 30 seconds, the LCD monitor switches off temporarily to reduce power consumption (The viewfinder lamp (green) blinks at 1-second intervals). Pressing the Shutter button down halfway at this point restores the camera to the ready-to-shoot status. 2 If the camera is left unused for 90 seconds after the LCD monitor switches off, the camera is automatically switched off (the viewfinder lamp switches off). !G Pressing the Shutter button down halfway and then releasing it, the screen may go dark briefly because the flash is charging. flash charging power is reduced. OK ­ F USING THE SET-UP SCREEN 13 00 2 0 1 Press the "MENU/OK" button to display the menu. 2 Press "d" or "c" to select "F" OPTION and then press "a" or "b" to select "SET-UP". 4 Press "a" or "b" to select a menu option and then press "d" or "c" to change the setting. Press "c " for "FORMAT", "DATE/TIME", "qRESET" or "DISCHARGE". 5 After modifying the settings, press the "MENU/OK" button to confirm the changes. If the camera is left unused for about 2 minutes in Playback mode, during setup or while the LCD monitor is switched off, the camera is automatically switched off. However, the LCD monitor does not switch off if the camera is left unused for 30 seconds in Playback mode or during setup. Settings h Power saving "OFF" Because the camera is not switched to low power consumption mode, the batteries will run down more quickly. However, this function automatically switches the camera off if the camera is not used for approximately 2 minutes. N When the camera has switched off N To restore power to the camera, slide the "POWER" switch to the ON position again. 4 0 5 0 !G Always switch the camera off when replacing the batteries. Opening the battery cover or disconnecting the AC power adapter without switching the camera off, the camera settings may revert to the default setting set at shipment. 46 47 SET-UP FORMAT Formatting erases all the frames (files). 2 Press the "MENU/OK" button to erase all the files and format the xD-Picture Card. Formatting erases protected files also. 5 Software Installation 5. 1 THE SOFTWARE COMPONENTS Connect the camera with " " selected as the USB setting (P. 60). [. . . ] Do not use chargers other than the specified model to charge the batteries. Any of these actions can cause the batteries to burst or leak and cause fire or injury as a result. Use only the batteries or AC power adapters specified for use with this camera. If the battery leaks and fluid gets into your eyes or comes into contact with your skin or clothing, this can cause injury or loss of eyesight. [. . . ]