User manual FUJIFILM FINEPIX_REAL 3D V1

[. . . ] BL00969-200 EN DIGITAL VIEWER Before You Begin First Steps Owner's Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM FinePix REAL 3D V1 digital viewer and the supplied software. Be sure that you have read and understood its contents before using the viewer. Viewing Pictures More Menu Options Connections Troubleshooting Appendix For information on related products, visit our website at http://www. fujifilm. com/products/index. html For Your Safety IMPORTANT SAFETY INSTRUCTIONS · Read Instructions: All the safety and operating instructions should be read before the appliance is operated. · Retain Instructions: The safety and operating instructions should be retained for future reference. [. . . ] 1 2 3 4 5 6 7 8 9 Memory card slot cover Stereo speakers T (power) button Tripod mount Hole for stand USB host connector Connector for AC power adapter Mini-B USB connector Memory card slot Viewer (back view) OPEN Page 8 -- 9 7 7 -- 9 25 8 4 Readying the Remote Control A battery is inserted in the remote control at shipment. Before using the remote control, remove the plastic insulating sheet from the battery chamber. 1 Note The battery supplied with the remote control is intended for trial use only. Replace the battery as described on page 6 if the remote control does not function as expected. Using the Remote Point the remote at the infrared receiver on the digital viewer. 3 m (9. 8 ft. ) or less First Steps Insulating sheet Maximum vertical and horizontal angle approx. 30 ° 3 Caution Do not place stickers or other obstructions over the infrared receiver. 5 Readying the Remote Control Replacing the Battery If the remote control does not function as expected, replace the battery with a fresh CR2025 battery (available separately from third-party suppliers). 1 Turn the remote control over and remove the battery holder. Remove battery holder, keeping latch pressed to right Remove the old battery 2 "+" indicator uppermost. from the holder and insert a fresh battery as shown, with the 3 Caution Insert the battery in the correct orientation. 3 Slide the holder into the remote control until the latch clicks into place. 6 Attaching the Stand Attach the stand to the frame. a towel 1 Placedown onor other soft cloth on a level surface such as a table and place the viewer face the cloth. 2 Gently screw the stand into the hole on the back of the viewer as shown. First Steps 3 Stand the viewer as shown. Wide orientation Tall orientation 1 Note The stand can be used in tall orientation when viewing D images, but must be in wide orientation to provide a C effect with C images. Tall orientation pictures can be rotated for display in wide orientation using the ORIENTATION option in the setup menu. 3 Caution The viewer should only be used on a table or other flat horizontal surface; do not hang the viewer from a picture hook or mount it on a wall or other vertical surface using double-faced tape. 2 Tip: The Tripod Mount The viewer can also be placed on a tripod using the tripod mount. 7 Inserting Memory Cards The viewer can be used with the memory cards listed on page 29 (for information on supported file formats, see page 30). Before inserting memory cards into the viewer, be sure to copy any important files to a computer. To insert a memory card: 1 Open the card slot cover. 1 Note The viewer turns off automatically when the cover is opened. shown by 2 Holding the memoryitcard asinto place. the indicator next to the memory card slot, slide the card in until clicks xD-Picture card SD/SDHC card 3 Caution Be sure the card is in the correct orientation; do not insert it at an angle or use force. 1 Note The viewer may be unable to display files that have been modified with a computer. Removing Memory Cards Open the card slot cover, gently press the card in, and release it slowly. 3 Caution The memory card may spring out if you remove your finger immediately after pushing the card in. 8 Turning the Viewer On Connect the supplied AC power adapter and turn the viewer on. adapter to the viewer as shown and then plug the adapter First Steps 3 Caution Use only the supplied AC power adapter. Do not use the viewer with other power adapters. Press the power button to turn A welcome 2 and then a slide show will beginthe viewer on. accompaniedscreen will be displayed automatically, by background music. POWER SLIDE SHOW 3D / 2D DISP /BACK VOLUME PARALLAX 1 Notes · If no pictures are available when the viewer is turned on, either because the memory card inserted in the viewer contains no pictures or there are no pictures in internal memory when no memory card is inserted, the main menu (pg. Demo Images and Background Music The viewer ships with a slide show in internal memory consisting of demo images illustrating some of the product's key features and accompanied by a background track. If no memory card is inserted when the viewer is turned on, the demo slide show will begin automatically (if a memory card is inserted, the viewer will instead display the images on the memory card). The sound track can be turned off by selecting OFF for MUSIC in the SLIDE SHOW menu (pg. [. . . ] 250 cd/m 2 (display alone) 512 MB Mini-B USB device connector · Infrared data port for data transfer · Infrared receiver for remote control · Still images: JPEG, multi-picture format · Movies: AVI, 3D-AVI AC 100 V ­ 240 V, 50/60 Hz using supplied AC power adapter · C: Approx. (including stand) Memory card slot xD-Picture Card/SD/SDHC Notices · Specifications subject to change without notice. FUJIFILM shall not be held liable for damages resulting from errors in this manual. · Although the display is manufactured using advanced high-precision technology, a small number of pixels (less than 0. 01%) may always be lit or may not light. [. . . ]