User manual FUJIFILM FINEPIX S9500

[. . . ] 1 2 3 4 5 6 OWNER'S MANUAL This manual will show you how to use your FUJIFILM DIGITAL CAMERA FinePix S9000/FinePix S9500 correctly. Please follow the instructions carefully. Getting Ready Using the Camera Advanced Features Settings Software Installation Viewing Images BL00472-200 (1) Warning To prevent fire or shock hazard, do not expose the unit to rain or moisture. EC Declaration of Conformity to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. You are cautioned that any changes or modifications not expressly approved in this manual could void the user's authority to operate the equipment. [. . . ] However, if there is insufficient space on the media for 3 shots, no picture will be taken. 2 CANCEL ALL 320 F5. 6 N6 ISO 200 From the 2nd shot onwards, the yellow "·" icon appears on the screen. 70 71 PHOTOGRAPHY MENU PHOTOGRAPHY MENU Displaying the menus (P. 63) Ê USING AN EXTERNAL FLASH Available Photography modes: N, M, <, > Select "ON" in this setting when using an external flash unit. can be used. 1 4 F External flash settings (for flashes with automatic flash control) EXTERNAL FLASH 1 2 : STD : STD : STD : 1 3 EV : OFF : OFF ON OFF !the white balance (P. 66) to "AUTO" or custom white balance (P. 73). 1 20 1 Close the built-in flash. 2 Mount the external flash on the camera's hot shoe and tighten the locking screw. For external flash, refer to the user's manual for the flash and specify the settings as described below. Set the flash for the aperture setting measured by Illustration is display of the external flash (commercial available). h Match the sensitivity setting ( P. 61) to the setting on the camera. CUSTOM 1 When the white balance is incorrect Adjust the white balance to match the external flash. In "»" WHITE BALANCE in the photography menu (P. 66), select "O, P" custom white balance. Press the "MENU/OK" button. 1 2 2 0 Hot shoe : OFF : AUTO : OFF : :0 : SET AUTO ! If you pop up the built-in flash when the external flash is set to "ON", the built-in flash fires once as a signal for the external flash to fire. The hot shoe and the Synchronizing terminal do not make a signal for flash. Ordinary external flash units can be used. However, some camera-specific flash units cannot be used. 3 Advanced Features Using a Synchronizing terminal Synchronizing terminal Attach the synchronization cord from the external flash to the Synchronizing terminal on the camera by pushing the cord into the terminal securely. Hold a sheet of white paper so that it fills the entire screen. When pressing the shutter button, the flash fires and the white balance is set. Click Synchronizing terminal cap Synchronization cord ! After taking the picture, check the color (white balance) setting for the image. i Set "IMAGE DISP. " to "1. 5 SEC", "3 SEC" or "CONT" in the SET-UP menu (P. 101). i Set the Power switch to "w" (P. 31). 3 The mode can be set to "N", "M", "<" (P. 41, 42, 43) or ">" (P. 44), but the use of "<" or ">" is better. N6 ISO 200 OVER OVER or UNDER ! Flash photography cannot be used when Top 4-frame continuous shooting (P. 54) or auto bracketing (P. 54) is selected. When [OVER] or [UNDER] appears, the white balance was not measured at the correct exposure. Set the exposure compensation again, using a negative value (­) when [OVER] appears and a positive value (+) when [UNDER] appears. 72 73 PLAYBACK FUNCTIONS PLAYBACK INFORMATION Use this function to check the photography information. Hold down the "INFO" button to check the information. PLAYBACK MENU Ò ERASING SINGLE / ALL FRAMES 2 0 1 Set the Power switch to "w". 2 Press the "MENU/OK" button to display the menu on the screen. 1 10 ! This function cannot be used during multi-frame playback (P. 31). Erased frames (files) cannot be recovered. Back up important frames (files) onto your PC or another media. Quality mode Sensitivity Shutter speed / Aperture FinePix COLOR Saturation Contrast Flash White balance Exposure compensation setting F ISO 400 1/500 4 :STD :STD :STD :OFF :AUTO :0 100-0001 Frame number 1 20 2 0 1 Press "a" or "b" to select "Ò" ERASE. 2 Press "c". ERASE Histogram 1 2 FRAME ALL FRAMES 8/24/2005 10:00 AM Highlight warning Highlight warning: When the image is overexposed, areas where white blooming has occurred flash black. 1 30 2 0 1 Press "a" or "b" to select "FRAME" or "ALL FRAMES". [. . . ] The use of other power sources can cause a fire. Do not use in the bathroom or shower. CAUTION Do not use this camera in locations affected by oil fumes, steam, humidity or dust. Do not leave this camera in places subject to extremely high temperatures. Do not leave the camera in locations such as a sealed vehicle or in direct sunlight. Do not pull on the connection cord to disconnect the AC power adapter. [. . . ]