User manual FUTABA MC601C
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FUTABA MC601C. We hope that this FUTABA MC601C user guide will be useful to you.
Manual abstract: user guide FUTABA MC601C
Detailed instructions for use are in the User's Guide.
[. . . ] f f
, f
MOUNTING PRECAUTIONS
f
v , w l f v f , w b bl , f
If v ,
MC601C
w f f l w
v ,
w v v v Nv
v bl
f
v
v v
MC601C
NSTRUCTION ANUAL
FEATURES
· SMD MOSFETs with smallest internal resistance for minimal losses and maximum power · PWM frequency is Performed by load adaptive · Heat protector · Low-voltage protection function · Fuse 40A (Buttery reverse plotection / Overload plotection) · Power left on alarm function · Serial communication function
Accessories
f f b b v b
If
Alw
w
,
Thank you for purchasing an MC601C . The MC601C is a high-frequency drive FET speed control developed for model electric cars. It is compact and light weight competition speed control, and uses a simple digital setting system.
MOUNTING PRECAUTIONS
Applicable motors Use the MC601C with a motor with 9 turns or more.
*If a motor with a number of turns smaller than the above is used, the heat protector and overcurrent protection circuit may operate. [. . . ] (Black) is minus.
Silicone flex wire Red Silicone flex wire Blue
In set-up mode MC601C stores every step when you press the Set-up button. All the settings are stored in the unit even when the speed control is subsequently disconnected from the battery. Set up the following basic functions on your transmitter (if present): ATV, EPA (throttle travel) - maximum Low ATV, EPA, ATL (brake travel) - maximum P exponential) - start with 0 TH trim - center Throttle reverse (servo reverse) - any setting; must not be changed after completion of set-up procedure. Asymmetrical stick travel is possible (2/3 throttle - 1/3 brake) If your transmitter does not feature these set-up functions, it is already in "basic set-up" mode. Remove the motor pinion, or ensure in some other way that the wheels of the model are free to rotate.
Motor connector
Terminal cover Silicone flex wire Red
Connects to the motor. If the motor rotates in the wrong direction, interchange the connections of this connector.
1
Turn on the power in following order.
Depending on the neutral position of the throttle stick, the red and green LED will blink simultaneously (orange) and a beeping sound will be repeated. (Alarm: Waiting for neutral data)
Power switch
2
Hold the SET button pressed in for at least 3 seconds using the small screwdriver supplied.
The SET LED flashes green, to indicate that the unit is in set-up mode.
* Since the data is read at the end of setting of all points, the points cannot be set independently. * If the amp power was turned off during setting, the setting points cannot be memorized. (The previous settings are retained. ) * The confirmation beep sounds only when the motor was connected. * If you make a mistake during the set-up procedure, an setting is not completed. : switch MC601C off and start again from the first step. * Check the operation by the following "LED DISPLAY. " When throttle operation and the CHECKER LED DISPLAY are not correct, set up again from the first step.
Pushbutton switch
LED
Transmitter throttle operation
MC601C
SET button operation
LED
3
Receiver connector Connects to the receiver throttle channel (CH2).
Neutral point setting
N
LED goes out and the
Neutral state Press SET button once.
motor beeps. flashes green two times and the motor beeps.
LED goes out
4 5
High point setting Brake MAX point setting
N
Full high state
Press SET button once.
POWER CAPACITORS
Power Capacitor stores battery energy and supplies this to the motor additionally when extra power is required. [Reference] The MC601C has excellent acceleration and throttle follow-up, but use this power capacitor when the course to be run requires more than maximum power. However, on a small technical course, not using the power capacitor may also be effective.
Solder the suppressor capacitors and the Schottky diode to the motor.
Motors with no suppressor capacitors, or inadequate suppression, may cause the MC601C to malfunction. The schottky diode improves the efficiency of the speed control / motor combination and provides extra protection to the brake FETs. The white ring must always face the positive side.
N
Full brake state
Press SET button once.
flashes green three times and the motor beeps.
LED goes out
Suppressor capacitors
This completes the set-up procedure.
LED DISPLAY
The MC601C operating state can be checked with the LED as shown below.
(Amp power left on alarm)
Operation Brake MAX point
[INSTALLATION]
See the pictures for the example of installation.
Schottky diode
Brake
Neutral point
Foward
High point
When the transmitter power was turned off first.
1 Remove the terminal cover from the MC601C. [. . . ] Low battery protection: When the power supply voltage drops, the output current to the motor is limited and supply voltage to the receiver is ensured. When the power supply voltage drops to the set voltage (initial setting 3. 0V), a protection circuit operation alarm is activated and output to the motor is cut. The protection circuit is automatically reset by recovery of the power supply voltage.
Phone: (043) 296-5119 Facsimile: (043) 296-5124 ©FUTABA CORPORATION 2007, 07
Terminal cover
(+;positive) Heat shrink tube (positive = red / negative = black)
Be careful when soldering to the tags on the speed control; don't overheat the tags with your soldering iron and take great care to avoid short-circuits between two of the three tags on the speed control.
Such a short-circuit would destroy the speed control.
FUTAB
A
Techno Garden Bldg. , B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FUTABA MC601C
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FUTABA MC601C will begin.