User manual GAGGENAU AH360720

[. . . ] Operating and assembly instructions AH 360-720 Extractor hood AH 360-720 Preface Safety notes 1. Important notes 1. 1 For your safety 1. 2 Operating for the first time 1. 3 About use 2. Structure and operating principle 2. 1 Structure of the appliance 2. 2 Accessories/special accessories 2. 3 Operating principle 3. Maintenance Page 3 Page 4-5 Page 4 Page 5 Page 5 Page 6-7 Page 6 Page 6 Page 7 Page 8-9 Page 8 Page 9 Page 10-11 Page 12 1 Preface With your new extractor hood, working in the kitchen will be even more fun. [. . . ] You can recommence operation by turning a knob or by pressing any key. Fig. 6 0 0 1 2 Switching off ­ Turn the "Ventilation level" control knob to the 0 position (Fig. To do this, turn the "Light" control knob to the (Light) position. Fig. 7 0 0 1 2 3 Switching on the Coanda level ­ Turn the "Ventilation level" control knob to the level you require. ­ The level you have set and the Coanda level symbol appear on the display (Fig. Note: You can change to any ventilation level, and the Coanda level remains set. Switching off the Coanda level ­ Press the "Coanda level" key or turn the "Ventilation level" knob to the 0 position. Fig. 8 8 3. 2 Special functions 0 0 1 2 3 Intensive level You should select the intensive level when browning and frying in an open pan. After a few minutes, the appliance switches back automatically to the previously selected ventilation level. The appliance is now operated at the intensive level for a few minutes and then switches off automatically. Ending the intensive level prematurely: ­ Turn the "Ventilation level" knob to the 0 position or ­ turn the "Ventilation level" knob to any level or ­ press the intensive level key once again. Fig. 10 Delayed shut-off Switching on: ­ Press the (Delayed shut-off) key. ­ The (Delayed shut-off) symbol and ventilation level 2 light up on the display (Fig. or ­ Turn the "Ventilation level" control knob to any level. ­ The (Delayed shut-off) symbol and the set ventilation level light up on the display (Fig. Switching off: ­ Turn the "Ventilation level" control knob to the 0 position. Cleaning the grease filters: The (Grease filter saturation) symbol flashes on the display after an operating time of 30 hours. Flashing of this symbol signals to you that the grease filters have to be cleaned. The grease filters can be cleaned at any time, even if the (Grease filter saturation) symbol does not flash. Proceed as follows: ­ Grip the grease filter handles and press the slide towards the rear. ­ Pull the grease filter out of its mount in the downward direction (Fig. You can clean the metal grease filters in a dishwasher at a maximum temperature of 150 °F / 65 °C. [. . . ] Exhaust air pipes should have a nominal diameter of 6 ´ ´ / 150 mm. Pay particular attention to ensuring that ­ the exhaust air ducts and pipes are kept as short as possible ­ the pipes are not laid at an acute angle, but as bends and that they are inserted into the shaft at an inclined upward angle and ­ there are no cross-sectional constrictions in the upward direction (this reduces the volume flow). As standard, the blow-out opening of the wall hood is in the upward direction. To pass exhaust air through the outer wall, we recommend the use of our telescopic wall box TM 150-045 (Ø 6 ´ ´ / 150 mm). [. . . ]