User manual GAGGENAU AI200700

[. . . ] Operating and Assembly Instructions AI 200-700 Extractor Hood AI 200-700 Preface Safety notes 1. Important notes 1. 1 For your safety 1. 2 Operating for the first time 1. 3 About use 2. Assembly instructions 6. 1 Technical data 6. 2 Installation Page 3 Page 4-5 Page 4 Page 5 Page 5 Page 6 Page 7-9 Page 10-11 Page 12 Page 13-18 Page 13 Page 14-18 1 Preface With your new extractor hood, working in the kitchen will be even more fun. The appliance offers you a number of advantages: ­ a good extraction capacity with low noise values, ­ a large number of control functions, ­ optimum illumination of the cooking surface by a dimmable halogen light. [. . . ] You set the fan level required for each respective cooking situation by pressing the function selector keys 1, 2, 3 or Int. or or or Fig. 5 7 The Int key for the intensive level should be pressed when browning and frying in an open pan (see Fig. If you have switched on the hood by selecting the intensive level, it will be switched off again automatically after 5 minutes. Fig. 6 If you press the Int key while the hood is running at fan level 1, 2 or 3, the electronic control will switch back automatically to the previously selected fan level after 5 minutes (see Fig. 7 If you would like to end the intensive level before the five minutes have elapsed, press the 0 key ("Motor off") or select a different level (see Fig. It is possible to switch off the extraction function at any time by pressing the 0 key (motor "off"). Fig. 8 8 Special functions: Intensive time: You can set the intensive level running time to 3, 5 or 10 minutes by simultaneously pressing the Int key and the 1, 2 or 3 key and you can store this setting (see Fig. First press the required key 1, 2, 3 or Int and then press the key (see Fig. After these ten minutes, the ventilation switches off, but the lighting stays on. or or or Fig. 11 or or Interval ventilation: Interval ventilation is a special feature of this appliance which periodically activates the fan for five minutes every hour. You can activate this function by simultaneously pressing the 0 key and, depending on the required extraction capacity, the 1, 2 or 3 key (see Fig. This mode of operation is indicated by alternating illumination of the key together with the corresponding fan level indicator. You can switch off interval ventilation by pressing the 0 key (see Fig. Cleaning and care Cleaning the grease filters The grease filter saturation display F flashes after an operating time of 30 hours to you indicate to you that you should clean the grease filter (see Fig. The grease filters can of course be cleaned at any time, even if the grease filter saturation display has not started to flash. The stainless steel grease filters can be removed easily for cleaning (see Fig. Then pull the grease filter downwards out of the holder; repeat the operation for the other grease filters. You can clean the stainless steel grease filters in a dishwasher at a maximum temperature of 130 °F / 55 °C, where it should be supported vertically to allow food or rinsing residues to drain off. If possible, the inner parts of the housing should be wiped out in hot rinsing water when replacing the filters. Caution: when cleaning the inside of the housing, beware of protruding parts. Fig. Repairs may only be carried out by authorised technicians, in order to guarantee the safety of the appliance. Unauthorised tampering with the appliance will invalidate any warranty claims. [. . . ] Before marking the securing holes, make sure that no electricity wires or water pipes or other wires/ pipes are laid at the drilling points in the ceiling. Before installation check the enclosed wall plugs and screws are suitable for your ceiling. Using the drilling template mark the position of the screws on the ceiling. Both screws are placed in a position, in which at a later stage of the installation the key-holes of the supporting frame are found (namely back left and front right from the control panel of the hood). [. . . ]