User manual GAGGENAU AI281120

[. . . ] Gaggenau Operating and installation instruction Extractor hood AI 280120 AI 281120 Fig. 1 ELECTRIC 2 Table of Contents Operating Instructions Installation Instructions Operating modes Exhaust-air mode Circulating-air mode Coanda effect Operating for the First Time If you encounter a problem Safety instructions Operating procedure Intensive setting Special functions Filters and maintenance Grease filters Saturation indicator F Activated carbon filter Cleaning and care Replacing the light bulbsn 4 4 4 5 6 6 7 8 9 9 10 10 10 11 12 13 Important information Prior to installation Exhaust-air mode Circulating-air mode Preparing the wall Electrical connection Installation 15 16 16 17 18 19 20 3 Operating modes Exhaust-air mode Circulating-air mode · Installation accessories for exhaust air mode. Ventilation duct AD280/281-016 for ceiling heights of 2. 27­2. 44 m AD280/281-026 for ceiling heights of 2. 44­2. 76 m AD280/281-036 for ceiling heights of 2. 76­2. 98 m. · Installation accessories for circulating air mode. Ventilation duct AD280/281-126 for ceiling heights of 2. 44­2. 76 m AD280/281-136 for ceiling heights of 2. 76­2. 98 m. . · · · · · · · An activated carbon filter must be fitted for this operating mode (see Filters and maintenance). [. . . ] Removing and inserting the metal grease filters: IMPORTANT: The lighting must be switched OFF and cool. 1 Press the catch on the grease filters inwards and fold the filters down. At the same time take hold of the underside of the grease filters with your other hand. Saturation indicator: F The grease filter saturation display F flashes after an operating time of 30 hours to you indicate to you that you should clean the grease filter. The grease filters can of course be cleaned at any time, even if the grease filter saturation display has not started to flash. 2 3 4 Clean the filters. ­ Press the button F. Cleaning the metal grease filters: · · · In normal operation (1 to 2 hours daily), the metal grease filter must be cleaned 1 x a month. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. · When cleaning the filters by hand, soak them in hot soapy water first of all. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. 10 Activated carbon filter For neutralizing odours in recirculating mode. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Installation and removal: IMPORTANT: The lighting must be switched OFF and cool. . 1 2 Remove the metal-mesh filters (see "Removing and inserting the metal-mesh grease filters"). 2 3 4 Remove the metal-mesh filters (see "Removing and inserting the metal-mesh grease filters"). Carefully remove the glass panes. 5 Remove the sockets for the fluorescent light bulbs. 6 Replace the fluorescent light bulbs with new ones available commercially (36 W, 840 Cool White, socket 2 G 11). Risk of breakage! 13 7 8 9 Insert the sockets for the fluorescent light bulbs. Tighten the screws for the mounting rails. 10 Insert the metal grease filters (see "Removing and inserting the metal grease filters"). 11 Restore the power by inserting the mains plug or switching on the fuse. Note: If the light does not function, check that the bulbs have been inserted correctly. 14 $ Important information Additional information concerning gas cookers: When installing gas hotplates, comply with the relevant national statutory regulations (e. g. Always comply with the currently valid regulations and installation instructions supplied by the gas appliance manufacturer. Only one side of the extractor hood may be installed next to a high-sided unit or high wall. Minimum distance on gas hotplates between the upper edge of the trivet and lower edge of the extractor hood: 700 mm, Fig. Please contribute to a better environment by disposing of packaging materials in an environmentally-friendly manner. Please ask your dealer or inquire at your local authority about current means of disposal. [. . . ] If the earthed socket is no longer accessible following installation of the extractor hood, ensure that there is a permanently installed disconnector. If it is necessary to wire the extractor hood directly into the mains: The extractor hood should only be connected to the electricity supply by a properly qualified electrician. A suitable separator is a switch that has a contact gap of more than 3 mm and interrupts all poles. If the connecting cable for this appliance is damaged, the cable must be replaced by the manufacturer or his customer service or a similarly qualified person in order to prevent serious injury to the user. 18 Electrical data Are to be found on the name plate inside the appliance after removal of the filter frame. Before undertaking any repairs, always disconnect the extractor hood from the electricity supply. [. . . ]